Revell Control ATOMIUM Manual Del Usuario página 9

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 20
1 QUADRoCopTER
1A Bonnet
1B Front propeller (white)
1C Rear propeller (red)
2 REMoTE CoNTRoL
2A Antenna
2B Power LED
2C Trim control for forward and backward
flight
2D Controller for forward and backward
flight as well as banking
2E Trim control for banking
3 INSERTING BATTERIES (REMoTE CoNTRoL)
3A Unscrew the screw
3B Insert 4 x 1.5 V AA batteries
and remove the
and pay attention to the
cover
polarity, as shown in the
battery compartment.
4 ChARGING ThE QUADRoCopTER
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Unplug quadrocopter from the battery, switch off the remote control and insert the
charter into an active USB connection. The control LED on the charger illuminates red
(4A).
• Remove the battery from the battery compartment (do not hold by the cable!) (4B).
• Now plug the battery into the cable of the USB charger. Pay attention to the polarity
in the process. Please do not use force. The red LED on the charger illuminates when
the charging process begins.
• The charging process lasts approx. 60 minutes and must be continuously monitored.
The red LED on the USB charger goes out when the charging process is finished.
• Disconnect the battery from the charging unit and disconnect the charging unit from
the USB port after the charging is completed (4C).
16
1D Battery compartment
1E Battery connection cable
1F Battery plug connector
2F Button for the looping function
2G Button for flight speed
2H Display
2I Trim control for rotation
2J Controller for thrust and rotation
2K ON/OFF switch
3C Fit the cover on
again and screw it
in place.
The quadrocopter can fly for approx. 6-8 minutes after a charge time of
approx. 60 minutes.
Warning notice: The LiPo battery can become warmer during charging. If it should
become hot and/or changes to the surface begin to appear, immediately discontinue
the charging process!
5 START pREpARATIoN
The thrust controller (the left controller on the remote control) must point down before
being switched on (5A). Then move the ON/OFF switch (5B) on the remote control
to "ON" and the Power LED will begin to blink (5C). Connect the battery cable using
the connection cable (5D). The LED on the quadrocopter now starts to blink. Place
the quadrocopter on the ground so that the tail points toward you with the two red
propellers in the rear (5E). The quadrocopter needs around 5-10 seconds to initialise
the gyro and to establish the connection to the remote control. As soon as the LED on
the quadrocopter lights up green permanently, the connection for the remote control
has been established.
Warning! Be sure to place the quadrocopter on a level surface – the control electronics
aligns its neutral position to the surface!
6 TRIM ADJUSTMENT oF ThE CoNTRoL
The correct trim is a basic requirement for fault-free flying behaviour of the
quadrocopter. Its adjustment is simple, but it requires some patience and a feel for it.
Please observe the following instructions precisely: Carefully move the thrust control
up and raise the quadrocopter approximately 0.5 to 1 metre in altitude.
6A If the quadrocopter moves by itself slowly or quickly to the left or right ...
Press the trim control for banking incrementally in the opposite direction.
6B If the quadrocopter moves by itself slowly or quickly around its own axis ...
Press the trim control for rotation incrementally in the opposite direction.
6C If the quadrocopter moves by itself slowly or quickly forwards or
backwards ...
Press the trim control for forward and backwards flight incrementally in the opposite
direction.
17

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

23986

Tabla de contenido