GYS PROGYS 220E FV CEL Manual De Instrucciones página 19

All extension cables must have an adequate size and section, relative to the machine's voltage .
Use an extension that complies with national safety regulations.
ELECTRODE WELDING (MMA
CONNECTIONS AND RECOMMENDATIONS
• Connect the cables, electrode holder and earth clamp in the connectors,
CLAVIER MMA 200 A 125 x 90 mm
• Respect the welding polarities and intensities indicated on the electrodes boxes,
• Remove the electrode from the electrode holder when the machin is not in use.
COULEURS / COLORS :
• Your machine is equipped with 3 specific functions to Inverters :
BLANC / WHITE
- The Hot Start increases the current at the beginning of the welding.
PANTONE 427C
- The Arc Force increases the current in order to avoid the sticking when electrode enters in melted metal.
PANTONE 429C
- The Anti Sticking allows you to easily withdraw your electrode without damaging it in case of sticking.
NOIR / BLACK
VRD
HOT START
The grey areas are not useful for this mode.
SELECTION MODE
MMA
Press button several times until the LED lights up under the symbol
MODE
MMA PULSE
Press button MODE several times until the LEDs light up under the symbol
The MMA vertical up mode adds a current pulse which makes vertical up welding easier.
MAIN SETTINGS
1. Selection of the type of coating
Select the electrode coating type by holding button
2. Setting the welding current
Adjust the welding current using the main knob according to the electrode diameter and the type of connection to be made. The current selected is
indicated on the display.
3. Adjusting the Hotstart level
Press button until the LED lights up to the left of the symbol
Adjust the Hotstart level using the main control wheel, which is expressed as a percentage of the current selected. The Hotstart level is indicated on
the display.
4. Adjusting the Arcforce level
Press button until the LED lights up to the left of the symbol
Adjust the Arcforce level using the main dial, which is indexed from -10 to +10. The lower the Arcforce level, the softer the arc, the higher the Arcforce
level and the higher the welding overcurrent. The default value is 0.
WELDING PARAMETERS
PROGYS 220E FV CEL
Current input
230V
110V
AND MMA VERTICAL UP
2018/11/08
DÉCOUPE / CUT
BLANC TRANSLUCIDE / TRANSLUCENT WHITE
DÔMES / BUTTONS GUIDE DOIGT 1 MM
NOIR TRANSLUCIDE 70 % / TRANSLUCENT BLACK 70%
MMA TIG
press 3 s
A
Basic
7018
V
Rutile Pulse Pulse
6013
Cellulosic
6010
MODE
ARC FORCE
setup
memory
press 3s press 3s
I N V E R T E R
W E L D E R
MMA
for more than 3 seconds until the LED lights up under the desired electrode type.
MODE
Length - Extension selection
< 45m
2.5 mm²
2.5 mm²
)
CLAVIER MMA 200 A
COULEURS / COLORS :
BLANC / WHITE
PANTONE 427C
PANTONE 429C
NOIR / BLACK
VRD
The grey areas are not useful for this mode.
.
and to the right of the symbol
.
HOT START
.
ARC FORCE
< 100m
4 mm²
125 x 90 mm
DÉCOUPE / CUT
BLANC TRANSLUCIDE / TRANSLUCENT WHITE
DÔMES / BUTTONS GUIDE DOIGT 1 MM
NOIR TRANSLUCIDE 70 % / TRANSLUCENT BLACK 70%
MMA
press 3 s
A
Basic
7018
V
Rutile Pulse
6013
Cellulosic
6010
HOT START
ARC FORCE
setup
memory
press 3s press 3s
I N V E R T E R
W E L D E R
MMA VERTICAL UP
Pulse
.
EN
2018/11/08
TIG
Pulse
MODE
19