Sony KLV-S20G10 Manual Del Usuario

Installing the Wall-Mount Bracket to the TV
English
To Customers:
For product protection and safety reasons, Sony strongly recommends that wall-
mounting of your TV be performed by a reliable licensed contractor. Do not attempt
to install it yourself.
Your KLV-S20G10 can be wall-mounted using SU-WL11 Wall-Mount Bracket (sold
separately). Please provide your contractor with this installation supplement as well
as the Instructions (supplied with SU-WL11 Wall-Mount Bracket). Read these
documents carefully for safety and proper installation.
To Sony Dealers and Contractors:
Provide full attention to safety during the installation, periodic maintenance and
examination of this product.
Installation du support de fixation mural sur le téléviseur
Français
À l'attention des clients :
Par souci de protection du produit et pour des raisons de sécurité, Sony recommande
vivement que l'installation du support de fixation mural de votre téléviseur soit
confiée à un installateur qualifié agréé. N'essayez surtout pas de procéder vous-même
à l'installation.
Le KLV-S20G10 peut être fixé au mur à l'aide du support de fixation mural
SU-WL11 (vendu séparément). Fournissez à l'installateur ce supplément
d'installation, ainsi que le mode d'emploi (fourni avec le support de fixation mural
SU-WL11). Lisez attentivement ces documents qui concernent la sécurité et
l'installation adéquate.
À l'attention des revendeurs Sony et des installateurs :
Accordez une attention particulière à la sécurité lors de l'installation, de l'entretien
périodique et de la vérification de ce produit.
Instalación del soporte de montaje mural en el televisor
Español
Para los clientes:
Por razones de protección del producto y de seguridad, Sony recomienda que el
montaje mural del televisor sea realizado por un contratista autorizado de Sony.
No intente instalarlo usted mismo.
Puede instalarse el modelo KLV-S20G10 en una pared mediante el soporte de
montaje mural SU-WL11 (se vende por separado). Muestre al contratista este
suplemento para la instalación, así como el manual de instrucciones (suministradas
con el soporte de montaje mural SU-WL11). Lea atentamente estos documentos para
realizar la instalación correctamente y de manera segura.
Para distribuidores y contratistas de Sony:
Ponga especial atención a la seguridad durante la instalación, mantenimiento
periódico y comprobación de este producto.
© 2005 Sony Corporation
Printed in Taiwan
English
Installing the TV
on a wall
The TV can be installed on a wall by attaching a Wall-
Mount Bracket (sold separately).
Verify your TV's model number and be sure to use the
bracket specified for your model only. Refer to the
Steps on this leaflet along with the Instructions
supplied with SU-WL11 Wall-Mount Bracket, to
properly carry out the installation.
Sufficient expertise is required in installing this
product, especially to determine the strength of
the wall for withstanding the TV's weight. Be sure
to entrust the attachment of this product to the
wall to Sony dealers or licensed contractors and
pay adequate attention to safety during the
installation. We are not liable for any damage or
injury caused by mishandling or improper
installation.
For customers with
KLV-S20G10
Install the SU-WL11 Wall-Mount Bracket (sold
separately).
Step 1: Check the parts
Open the Wall-Mount Bracket package and check the
contents for all required parts along with the
Instructions.
Step 2: Decide the location
Decide where you want to install your TV. Turn to the
back cover of this leaflet for the display installation
dimensions and determine the location.
Refer to the Instructions for the SU-WL11.
1
(US)
KLV-S20G10
2-633-137-01(1)
Step 3: Attach bracket A to the
wall
Attach bracket A to the wall.
Refer to the Instructions for the SU-WL11.
Step 4: Remove the Tabletop
Stand from the TV
Before removing the Tabletop Stand, disconnect all the
cables from the TV.
Refer to the Instructions for the SU-WL11.
Pull the rear cover out from the
1
bottom of the TV, then remove
from the top.
To prevent damaging the surface of the LCD
display, place the TV on a soft mat.
Note
Lay the display face down on a stable and level
surface with the Tabletop Stand hanging over
the edge of the surface. Having the display face
and the base of the Stand on the same level
surface will create unstable working condition
and can damage the unit.
Rear cover
Soft mat
English Installation dimensions table
Français Tableau des dimensions pour l'installation
Español Tabla de las dimensiones de instalación
KLV-S20G10
A
B
168(6 5 / )
8
Display Model/ Display Dimensions/ Unit: mm (inches)/
Dimensions de l'écran/ Unité : mm (pouces)/
Modèle d'écran/
Dimensiones de la pantalla Unidad: mm (pulgadas) Longitud de cada ángulo de montaje
Modelo de
A B C D
pantalla
504 467 110 23
KLV-S20G10
7 1 3 29
(19 / ) (18 / ) (4 / ) ( / )
8 2 8 32
* The wall must be strong enough to support at least four times the weight of the display that you are installing./
* Le mur doit être suffisamment solide pour supporter au moins quatre fois le poids de l'écran que vous installez./
* La pared debe ser suficientemente resistente para soportar como mínimo cuatro veces el peso de la pantalla que está instalando.
Remove the four screws as shown
2
below, and remove the Tabletop
Stand from the TV.
Note
Hold the Tabletop Stand firmly while removing
the last screw.
Tabletop
Stand
Step 5: Attach brackets B, C, D,
and E to the TV
Refer to the Instructions for the SU-WL11.
Attach bracket B to the TV.
1
Using the four screws which were removed in
Step 4, secure bracket B to the TV.
Bracket B
Connect the cables.
2
For details on the cable connection, refer to the
Operating Instructions for your TV.
F
G
D
C
H
E
B
Length for each mounting angle/ Unit: mm (inches)/
Longueur de chaque angle de montage/ Unité : mm (pouces)/
Unidad: mm (pulgadas)
Mounting angle ( α °)/
Angle de montage ( α °)/
F G
E
Ángulo de montaje( α °)
0° 155 (6 1 / ) 64 (2 5 / ) 289 (11
8 8
266
5° 177 (7) 53 (2 1 / ) 299 (11
8
1
(10 / )
2
10° 198 (7 7 / ) 40 (1 5 / ) 308 (12
8 8
Determine the mounting angle
3
then choose a bracket C that
corresponds to your desired angle.
Bracket C comes in three
different tilting angles. Attach
bracket C to B by using two of
the supplied screws.
The angle 0°, 5°, or 10° is
marked on the side of
bracket C.
Bracket C
Attach bracket D to bracket C,
4
and secure the brackets together
with two of the supplied screws.
Bracket D
Attach bracket E to bracket C,
5
and secure the brackets together
with two of the supplied screws.
Bracket E
Step 6: Secure the TV to the wall
Refer to the Instructions for the SU-WL11.
Weight/
Poids/
Peso
(×4)*
H
1 / ) 7.5 kg
2
(16 lb 09 oz)
7 / )
8
(30 kg
1 / ) (66 lb 03 oz))
4
Shaft
2
(US)