Campbell Hausfeld TL140289 Instrucciones De Funcionamiento página 2

Operating Instructions
General Safety
Information (Continued)
9 . Never trigger the tool when
not applied to a work object .
Attachments must be securely
attached . Loose attachments can
cause serious injury .
10 . Protect air lines from damage or
puncture .
11 . Never point an air tool at oneself
or any other person . Serious injury
could occur .
12 . Check air hoses for weak or worn
condition before each use . Make
sure all connections are secure .
Release
all
pressure from the system
before attempting to install,
service, relocate or perform
any maintenance.
13 . Keep all nuts, bolts and screws tight
and ensure equipment is in safe
working condition .
14 . Do not put hands near or under
moving parts .
Do not misuse
this product.
Excessive exposure to vibration, work in
awkward positions, and repetitive work
motions can cause injury to hands and
arms. Stop using any tool if discomfort,
numbness, tingling, or pain occur, and
consult a physician.
www.chpower.com
Operation
LUBRICATION
Proper lubrication is the owner's
responsibility . Failure to lubricate the air
tool properly will dramatically shorten
the life of the tool and will void the
warranty .
This impact wrench
requires lubrication
BEFORE the initial use and BEFORE and
AFTER each additional use.
Impact wrenches require lubrication
throughout the life of the tool and
must be lubricated and or greased in
two separate areas: the air motor and
the impact mechanism . Follow the
outlined procedures and refer to parts
manual for tool features . Campbell
Hausfeld air tool oil (ST127000AV) is
recommended because this oil cleans,
lubricates and inhibits rust all in one
step .
AIR MOTOR LUBRICATION
The motor must be lubricated daily . An
air motor cannot be oiled too often .
Disconnect the
impact wrench from
the air supply before lubricating.
1 . Disconnect the impact wrench from
the air supply .
2 . Turn the impact wrench upside
down .
3 . While pulling the trigger, squeeze
approximately a 1/4 oz . of Campbell
Hausfeld airtool oil in the air inlet .
Then, push the forward and reverse
button in both directions .
After an air tool
has been lubricated,
oil will discharge through the exhaust
port during the first few seconds of
operation. Thus, THE EXHAUST PORT
MUST BE COVERED WITH A TOWEL
before applying air pressure. FAILURE
TO COVER THE EXHAUST PORT CAN
RESULT IN SERIOUS INJURY.
4 . Connect the impact wrench to the
air supply and cover the exhaust port
with a towel (Refer to replacement
parts manual for tool features) .
Run the impact wrench in both the
forward and reverse directions for
20 to 30 seconds . Oil will discharge
from the exhaust port when air
pressure is applied .
2
IMPACT MECHANISM LUBRICATION
Lubricate the impact mechanism
monthly . See the enclosed yellow flyer .
Disconnect the
impact wrench from
the air supply before lubricating.
1 . Disconnect the impact wrench from
the air supply .
2 . Remove the slotted screw or allen
head screw from the oil port hole
(Refer to replacement parts list for
tool features) .
3 . Squeeze approximately 1 ounce of
Campbell Hausfeld air tool oil in the
oil port hole . Replace the screw .
4 . Reconnect the air supply to the
impact wrench and run for 20 to 30
seconds . Lubricate the entire impact
mechanism by rotating the tool
upside down and sideways while
running the tool .
5 . Remove the screw and hold the oil
port hole over a suitable container
to allow excess oil to drain .
Sometimes triggering the tool when
dumping the oils helps to force out
the excess oil .
6 . If the oil is dirty, repeat the
procedure above until the oil comes
out clear . Install the screw and
tighten . The residual oil remaining
in the impact mechanism chamber
is all that is needed for proper
lubrication .