Recommended Hookup - Campbell Hausfeld TL140289 Instrucciones De Funcionamiento

Operation (Continued)

RECOMMENDED HOOKUP

The illustration below shows the
recommended hookup for the tool .
1 . The air compressor
must be able to
maintain a minimum
of 60 PSI when the
tool is being used . An inadequate air
supply can cause a loss of power and
inconsistent driving .
2 . An oiler can be
used to provide oil
circulation through
the tool . A filter can
be used to remove liquid and solid
impurities which can rust or "gum
up" internal parts of the tool .
3 . Always use air supply hoses with
a minimum working pressure
rating equal to or greater than the
pressure from the power source if a
regulator fails, or 200 PSI, whichever
is greater . Use 1/4 inch air hose for
runs up to 50 feet . Use 3/8 inch air
hoses for 50 foot run or longer .
200 PSI or greater
3/8 inch I .D .
4 . Use a pressure regulator on the
compressor, with an operating
pressure of 0 PSI - 125 PSI . A pressure
regulator is required to control
the operating pressure of the tool
between 60 PSI and 90 PSI .
Recommended Hookup
SPEED ADJUSTMENT
The impact wrench should never
be used to set torque . Use a torque
wrench to set the torque . All models
are equipped with regulators for speed
adjustment (Refer to parts manual for
60 PSI
Min. tool features) .
90 PSI
To remove lugs or bolts, set the
Max.
regulator to the maximum setting .
When installing, always use a torque
wrench to attain the proper torque of
the lugs or bolts .
overtighten. Bolts may fail or cause a
hazardous condition. Be sure to set the
regulator to the minimum setting then
use a torque wrench to set torque.
AIR TOOL SET-UP
NOTE: It is not recommended to install
a quick coupler between the tool and
the whip hose .
Using fittings or air hoses which are
too small can create a pressure drop
and reduce the power of the tool . For
3/8, 1/2 and 3/4 inch impact wrenches
use 3/8 inch (I .D .) fittings with 1/4 inch
NPT threads . Most compressors are
shipped with a short, 1/4 inch I .D . hose .
For proper performance and more
convenience, use a 3/8 inch I .D . hose .
Hoses longer than 50 feet should have a
1/2 inch I .D .
For 1 inch impact wrenches use 1/2 inch
(I .D .) fittings with 1/2 inch NPT threads
and a 1/2 inch I .D . hose . Hoses longer
than 50 feet should have a 1 inch I .D .
pull the hose to move the tool or a
compressor. Keep hoses away from
heat, oil and sharp edges. Replace any
hose that is damaged, weak or worn.
Quick
Coupler
Quick
Plug
Air Hose
When reassembling
be careful not to
Never carry a tool
by the hose or
Regulator
Quick Plug
Lubricator
(Optional)
Quick Coupler
(Optional)
3
Storage
The impact wrench must be lubricated
before storing . Follow the air motor
lubrication instructions with an
exception to step 4 . Only run the impact
wrench for 2 to 3 seconds instead of 20
to 30 seconds because more oil needs
to remain in the impact wrench when
storing .
TECHNICAL SERVICE
For information regarding the
operation or repair of this product,
please call 1-800-543-6400 .
REPLACEMENT PARTS INFORMATION
For information regarding where to
order replacement parts, call toll free
1-800-543-6400 .
Please provide the following
information:
• Model number
• Stamped code
• Part number and description
Address parts correspondence to:
Campbell Hausfeld
100 Production Drive
Harrison, Ohio 45030 U .S .A .
Filter
www.chpower.com
TL140289