T-Post Installation - Levolor Shutters Instalación

ADDITIONAL INSTALLATION INSTRUCTIONS
T-POST INSTALLATION - T-POST ALIGNMENT BLOCK WITH 4-SIDED FRAME
(A) Installing Alignment Blocks (See Figure 11.1)
• Prepare the bottom and top frames with the alignment blocks for the assembly process.
• Align and stack two T-Post alignment blocks with the pre-drilled holes in the bottom frame.
• Using two #6 x 1 1¾" screws, hand tighten the alignment blocks to the frame. Do not
completely tighten screws down, ensuring that they can still move slightly. This will allow
some side to side adjustment of the T-Post.
• Once the two T-Post alignment blocks are secured to the bottom frame, repeat the steps
for the top frame.
(B) Assemble Frame and T-Post (Read Step 4 for specific Frame Assembly Considerations
before beginning) (See Figure 11.2)
• Insert the corner keys into the top and bottom frames. Align the left side frame for
insertion into the bottom frame. Slide the bottom corner key into the side frame, and
lightly tap using a rubber mallet until an audible "pop" is heard, indicating the frames
have been successfully secured. Repeat the same process for the right hand
side frame.
• Attach T-Post to the bottom frame by sliding the T-Post over the alignment blocks on
the bottom frame. Once this has been completed, the top frame should be secured in
the same manner as the side frames, making sure the T-Posts are aligned with the
alignment blocks on the top frame.
(C) Mark Location of T-Posts
• Test the fit and position of the panels to determine the exact location of the
T-Post. Using a pencil, mark the location of each T-Post, ensuring that the
non-hinge side gaps between the panels and frames are consistently 1/8" .
(D) Secure T-Post (Figure 11.3)
• Open or remove the panels, and align the T-Post with the pencil marks,
setting a #8 x 2" installation screw horizontally through the pre-drilled hole
in the side of the T-Post at the bottom.
• The screw will pass between the (2) T-Post alignment blocks, locking the
T-Post into position.
• Repeat for the top of the T-Post and cap installation holes with button
covers.
• Once the T-Post has been successfully secured, return to Step 8 to complete
Shutter installation process.
10
Shutters Installation Manual
MOTORIZATION
Install batteries or connect the power source, which is located in the bottom rail on the back of the Shutter panels.
• Open the shutter panel to access the battery cover(s).
• Slide the battery cover to unlock (slide towards the side
(Figure 11.1)
• Disconnect the motor wire.
T-Post
• Remove the battery wand from the battery cover.
Installation
Hole
• Pinch the tabs at the contoured end of the battery wand to release the end cap.
T-Post
• Remove batteries.
• Install new batteries per the diagram on the clear housing.
• Reinstall end cap of battery wand.
Note: AA Alkaline batteries are recommended; Lithium and rechargeable batteries are NOT recommended.
• Follow battery assembly installation instructions.
• Slide the battery cover to lock (slide away from the side of the panel with the program button), as
Frame
• Once there is power to the shutter, the manual control button will operate the louvers and the remote
(Figure 11.2)
• See remote guide for instructions on pairing the remote with the Shutter.
Align T-Post and Secure
#8 x 1 ⁄ "
1
2
Installation
Screw
(Figure 11.3)
of the panel Note: The illustrations are of a right hinge
panel with a motor in the bottom rail, the cover will
slide in the opposite direction on a left hinge panel with
the program button), as indicated on the face of the
battery cover, then rotate the battery cover with battery
wand towards you.
indicated on the face of the battery cover.
can be paired.
P1 L - No Motor & P1 R - With Moto &r P2 LR -With
Divider Rail Battery Wand Divider Rail Battery Wand Divider Rail
Motor & Motor &
Battery Wand Battery Wand
ADDITIONAL INSTALLATION INSTRUCTIONS
Tab Slot
Battery
Pack
Cap
Squeeze Latch
Panel
Couplers
Panel
Couplers
Shutters Installation Manual
11