Additional Safety Instructions - Scheppach HM80Lxu Traducción De Las Instrucciones Originales De Funcionamiento

12 Secure the workpiece
– Use the clamping devices or a vice to hold the
workpiece in place. In this manner, it is held more
securely than with your hand.
– An additional support is necessary for long work-
pieces (table, trestle, etc.) in order to prevent the
machine from tipping over.
– Always press the workpiece firmly against the
working plate and stop in order to prevent bounc-
ing and twisting of the workpiece.
13 Avoid abnormal posture
– Make sure that you have secure footing and always
maintain your balance.
– Avoid awkward hand positions in which a sudden
slip could cause one or both hands to come into
contact with the saw blade.
14 Take care of your tools
– Keep cutting tools sharp and clean in order to be
able to work better and more safely.
– Follow the instructions for lubrication and for tool
replacement.
– Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
– Check extension cables regularly and replace them
when damaged.
– Keep the handle dry, clean and free of oil and
grease.
15 Pull the plug out of the outlet
– Never remove loose splinters, chips or jammed
wood pieces from the running saw blade.
– During non-use of the electric tool or prior to main-
tenance and when replacing tools such as saw
blades, bits, milling heads.
16 Do not leave a tool key inserted
– Before switching on, make sure that keys and ad-
justing tools are removed.
17 Avoid inadvertent starting
– Make sure that the switch is switched off when
plugging the plug into an outlet.
18 Use extension cables for outdoors
– Only use approved and appropriately identified
extension cables for use outdoors.
– Only use cable reels in the unrolled state.
19 Remain attentive
– Pay attention to what you are doing. Remain sen-
sible when working. Do not use the electric tool
when you are distracted.
20 Check the electric tool for potential damage
– Protective devices and other parts must be care-
fully inspected to ensure that they are fault-free
and function as intended prior to continued use of
the electric tool.
– Check whether the moving parts function faultless-
ly and do not jam or whether parts are damaged. All
parts must be correctly mounted and all conditions
must be fulfilled to ensure fault-free operation of
the electric tool.
– The moving protective hood may not be fixed in
the open position.
22 GB/IE
– Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is specified
in the operating manual.
– Damaged switches must be replaced at a customer
service workshop.
– Do not use any faulty or damaged connection cables.
– Do not use any electric tool on which the switch
cannot be switched on and off.
21 ATTENTION!
– Exercise elevated caution for double mitre cuts.
22 ATTENTION!
– The use of other insertion tools and other acces-
sories can entail a risk of injury.
23 Have your electric tool repaired by a qualified elec-
trician
– This electric tool conforms to the applicable safety
regulations. Repairs may only be performed by an
electrician using original spare parts. Otherwise
accidents can occur.

ADDITIONAL SAFETY INSTRUCTIONS

Safety precautions
1
– Warning! Do not use damaged or deformed saw
blades.
– Replace a worn table insert.
– Only use saw blades recommended by the manu-
facturer which conform to EN 847-1.
– Make sure that a suitable saw blade for the mate-
rial to be cut is selected.
– Wear suitable personal protective equipment. This
includes:
– Hearing protection to avoid the risk of becoming
hearing impaired,
– Respiratory protection to avoid the risk of inhal-
ing harmful dust,
– Wear gloves when handling saw blades and
rough materials. Carry saw blades in a con-
tainer whenever practical.
– Wear goggles. Sparks generated during work or
splinters, chippings and dust coming from the
device can lead to loss of eyesight.
– Connect a dust collecting device to the electric tool
when sawing wood. The emission of dust is influ-
enced, among other things, by the type of material
to be processed, the significance of local separa-
tion (collection or source) and the correct setting
of the hood/guide plates/guides.
– Do not use saw blades made of high-speed alloy
steel (HSS steel).
2 Maintenance and repair
– Pull out the mains plug for any adjustment or re-
pair tasks.
– The generation of noise is influenced by various
factors, including the characteristics of saw blades,
condition of saw blade and electric tool. Use saw
blades which were designed for reduced noise
development, insofar as possible. Maintain the
electric tool and tool attachments regularly and if
necessary, initiate repairs in order to reduce noise.