Double Insulated Tools; Extension Cords - Bosch 3296 0 603 296 0 Manual Del Usuario

may result in a dangerous condition.
• THE USE OF ANY ACCESSORIES not
specified in this manual may create a hazard.
• MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for better and safer perfor-
mance. Follow instructions for lubricating and
changing accessories. Inspect tool cords peri-
odically and if damaged, have repaired by au-
thorized service facility. Inspect extension
cords periodically and replace if damaged. Keep
handles dry, clean and free from oil and grease.
• CHECK DAMAGED PARTS. Before fur-
ther use of the tool, a guard or other part that is
damaged should be carefully checked to deter-
mine that it will operate properly and perform
its intended function. Check for alignment of
moving parts, binding of moving parts, break-
age of parts, mounting, and any other condi-
tions that may affect its operation. A guard or
other part that is damaged should be promptly
and properly repaired or replaced. Have defec-
tive switches replaced. Do not use tool if switch
does not turn it on or off.
• ALL REPAIRS, ELECTRICAL OR ME-
CHANICAL, should be attempted only by
trained repairmen. Contact the nearest Bosch
Factory Service Center, or Bosch Authorized
Service Center or other competent repair cen-
ter. Use only Bosch replacement parts, any
other may create a hazard.
Safety Rules for Planers
• Always start the plane before contacting the
workpiece and never pull the plane backwards
on the workpiece.
• Unplug the power cord before making ad-
justments or changing/reversing blade sets.
• Make sure the spring operated automatic
retracting rabbet guard returns to blade cover-
ing position instantly.
• Do not put fingers or any objects into the chip
ejector or clean out chips while tool is running.
Remove plug from power source if it becomes
necessary to remove chips.
• Before planing, check the workpiece for nails.
If there are nails, either remove or set them well
below intended finished surface.
• Small workpiece must be adequately secured
so that the rotating planer knives will not pick it
up during forward motion of the planer.
BM 2609931094 6/95
• After changing blades, rotate the cutter drum
to make sure blades are not hitting any part of
the blade head housing and the blade locking
screws are tight.
• Wear protective gloves and safety goggles.
• Always hold the tool firmly with both hands.
• Never place the plane down until the blade is
completely at rest.

Double Insulated Tools

• Double Insulation
used in electric power tools which eliminates
the need for the three wire grounded power cord
and grounded power supply system. It is a
recognized and approved system by
Underwriter's Laboratories, CSA and Federal
OSHA authorities.
IMPORTANT:
double insulation requires care and knowledge
of the system and should be performed only by
a qualified service technician. WHEN SER-
VICE IS REQUIRED USE ONLY IDENTI-
CAL REPLACEMENT PARTS.
POLARIZED PLUGS: If your tool is equipped
with a polarized plug (one blade is wider than
the other), this plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install the
proper outlet. To reduce the risk of electric
shock do not change the plug in any way.
• Replace damaged cords immediately. Use of
damaged cords can shock, burn or electrocute.
• If an extension cord is necessary, a cord with
adequate size conductors should be used to
prevent excessive voltage drop, loss of power
or overheating. The table below shows the
correct size to use, depending on cord length
and amperage rating on the tool's nameplate. If
in doubt, use the next heavier gauge. Always
use U.L. and CSA listed extension cords.
6
6
is a design concept
Servicing of a tool with

Extension Cords

12/14/98, 4:19 PM