Ecco 6465 Serie Instrucciones De Instalación Y Funcionamiento

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

ECCO's 6465 Series is a low profile LED beacon with a long,
maintenance-free service life. 6465 Series beacons are ideal for
industrial vehicle applications and feature a
12-80 VDC operating range.
!
WARNING!
Failure to install or use this product according to manufacturer's recommendations may result in property damage, serious injury, and/or death to
those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the safety information
contained
1.
Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure
the safety of you and those you are seeking to protect.
2.
Exercise caution when working with live electrical connections.
3.
This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including fire.
4.
Proper placement and installation are vital to the performance of this warning device. Install this product so that output performance of the
system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system without losing
eye contact with the roadway.
5.
Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment
area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death. Refer to the
vehicle owner's manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable mounting location
ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6.
It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people,
vehicles or other obstructions.
7.
The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-
of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, driving against traffic, respond-
ing at a high rate of speed, or walking on or around traffic lanes.
8.
This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding
warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer as-
sumes no liability for any loss resulting from the use of this warning device.
Specifications:
Size:
Permanent Mount
Magnet Mount
Weight:
Permanent Mount
Magnet Mount
Voltage: Model 6465X 12-80 VDC systems
Model 6465X-MG 12-24 VDC systems
Current Draw:
Flash Rate: Pulse 8 flash mode:
Installation & Mounting:
Carefully remove the beacon and place it on a flat surface. Ex-
amine the unit for transit damage, broken lenses, etc. If damage
is found, contact the transit company or distributor. Do not use
damaged or broken parts.
Installation and Operation Instructions
W: 5.1" x H: 4.2"
W: 5.1" x H: 4.3"
0.6 lb.
1.6 lb.
100 mA
85 FPM
6465 LED Beacon
!
WARNING!
Maximum recommended vehicle speed for safe operation using
the Magnet Mount model is 65 mph (104 km/h) on a well main-
tained road, when fitted to the center of a vehicle roof of steel con-
struction. Higher speeds could cause the mount to fail, resulting
in the beacon flying off of the vehicle, which could cause damage
to other vehicles and injury or death to the passengers.
The magnet mount is not intended as a permanent mounting for the
beacon. The magnet mount unit must be mounted on a magnetic sur-
face (i.e. no fiberglass, etc.). Insure that the magnet is kept clean.
Mounting:
Permanent, Model 6465
Position the unit in the desired mounting location. Using the base
as a template, mark the mounting hole locations. Drill three 3/16"
mounting holes, and drill one hole for power wire routing. The use of
a grommet is recommended for wires passing through compartment
walls. Mount the beacon using #10 hardware.
Page 1 of 2

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Ecco 6465 Serie

  • Página 1 Installation and Operation Instructions 6465 LED Beacon ECCO’s 6465 Series is a low profile LED beacon with a long, maintenance-free service life. 6465 Series beacons are ideal for industrial vehicle applications and feature a 12-80 VDC operating range. WARNING! Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious injury, and/or death to...
  • Página 2: Replacement Parts

    Wiring: Important! This unit is a safety device, and it must be connected to its own The wiring for this configuration is as shown in Figure 1 below. The positive separate, fused power point to assure its continued operation should any line must have a 3 amp fuse, as shown.
  • Página 3: Especificaciones

    Instrucciones de instalación y uso, baliza LED 6465 La serie 6465 de ECCO es una baliza LED de bajo perfil con un servicio prolongado, libre de mantenimiento. Las balizas de la serie 6465 son ideales para aplicaciones en vehículos industriales y ofrecen un rango operativo de 12 a 80 V CC.
  • Página 4: Instalación Y Montaje

    Cableado: Instalación y montaje: El cableado para esta configuración es el que se muestra en la figura 1 a Retire la baliza con cuidado y colóquela sobre una superficie plana. Inspeccione continuación. La línea positiva debe tener un fusible de 3 amperes, según la unidad para determinar si se han producido daños durante el traslado, si se indica.
  • Página 5 Limitación de responsabilidad y garantía limitada del fabricante: El fabricante garantiza que al momento de la compra, este producto cumple con las especificaciones del fabricante para el mismo (disponibles a pedido). El fabricante garantiza además que el presente producto está libre de defectos en sus materiales y en su fabricación. Esta garantía limitada se extiende durante treinta y seis (36) meses a partir de la fecha de la compra.
  • Página 6: Caractéristiques Techniques

    Instructions d'installation et d'utilisation Balise DEL 6465 La série 6465 d’ECCO est une balise DEL discrète avec une longue durée de vie utile sans besoin de maintenance. Les balises de la série 6465 sont idéales pour les applications de véhicules industriels et ont une plage de fonctionnement de 12 à...
  • Página 7: Installation Et Montage

    Câblage : Installation et montage : Sortez délicatement la balise et placez-la sur une surface plane. Assurez-vous Le raccordement de cette configuration est tel que présenté dans la figure 1 ci- que l’unité n’a pas été endommagée par le transport, que les lentilles ne sont pas dessous.
  • Página 8 Garantie limitée et limitation de responsabilité du fabricant : Le fabricant garantit qu’à la date d’achat ce produit sera conforme aux caractéristiques techniques définies par ses soins (disponibles sur demande) et qu’il est exempt de vices de fabrication et de main-d’œuvre. La présente garantie limitée est valable trente-six (36) mois à compter de la date d’achat. D’autres garanties peuvent s’appliquer.

Este manual también es adecuado para:

X-6465amgX64656465x6465x-mg

Tabla de contenido