Ego Power+ CS1400E Manual Del Operador página 12

Ocultar thumbs Ver también para CS1400E:
Tabla de contenido

Publicidad

4. Place the chain drive links into the guide bar groove
EN
and make the chain a loop at the back of the guide
bar (Fig. J).
5. Hold the chain in position on the guide bar and place
the loop around the sprocket of the power head.
6. Slide the guide bar slot over the alignment flanges
until the tension adjusting pin is inserted in the lower
hole in the tail of the bar (Fig. L1).
NOTICE:
Small directional arrows are engraved in the
saw chain. Another directional arrow is molded into the
housing. When looping the saw chain onto the sprocket,
make sure that the direction of the arrows on the saw
chain will correspond to the direction of the arrow on the
housing. If they face in opposite directions, turn over the
saw chain and guide bar assembly (Fig. L2).
7. Replace the side cover and slightly tighten the side
cover knob.
8. Lift the tip of the guide bar up to check for sag
(Fig. K). Release the tip of the guide bar and turn the
chain tensioning knob clockwise. Repeat this process
until the sag is eliminated.
9. Tighten the side cover knob securely to ensure that
the saw chain is properly tensioned before using.
Fig. J & L parts description see below:
J-1 Chain Drive Links
J-2 Guide Bar Groove
L-1 Alignment Flange
NOTICE:
To extend the guide bar life, invert the bar
occasionally.
NOTICE:
If chain is too tight, it will not rotate. Loosen
the side cover knob slightly and turn the tensioning knob
once from right to left. Lift the tip of the guide bar up and
retighten the side cover knob securely. Assure that the
chain will rotate without binding.
ADJUSTING THE CHAIN TENSION
Stop the motor and remove the battery pack before
adjusting the chain tension. Make sure the side
cover knob is loosened. Turn the chain tensioning
knob clockwise to tension the chain. See the section:
"REPLACE THE BAR AND CHAIN" for additional
information.
A cold chain is correctly tensioned when there is no slack
on the underside of the guide bar and the chain is snug, but
it can be turned by hand without binding. The chain must
be re-tensioned whenever the flats on the drive links do not
sit in the bar groove.
12
56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS1400E/CS1600E
L-2 Tension Adjusting Pin
L-3 Guide Bar Slot
L-4 Sprocket
During normal saw operation, the temperature of
the chain will increase. The drive links of a correctly
tensioned warm chain will hang approximately 1.3 mm
out of the bar groove (Fig. M).
NOTICE:
New chains tend to stretch; check chain tension
frequently and tension as required.
NOTICE:
A chain tensioned while it is warm may be too
tight upon cooling. Check the cold tension before next
use.
OPERATION
WARNING:
Do not allow familiarity with this product
to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side
shields. Failure to do so could result in objects being
thrown into your eyes and other possible serious injuries.
WARNING:
Do not use any attachments or
accessories not recommended by the manufacturer of
this product. The use of attachments or accessories not
recommended can result in serious personal injury.
WARNING:
To prevent accidental starting that could
cause serious personal injury, always remove the battery
pack from the tool when assembling parts, making
adjustments, cleaning, or when not in use.
Before each use, inspect the entire product for damaged,
missing, or loose parts, such as screws, nuts, bolts, caps, etc.
Securely tighten all fasteners and caps and do not operate
this product until all missing or damaged parts are replaced.
APPLICATION
You may use this product for basic felling, limbing,
pruning and woodcutting of lumber and trees.
NOTICE:
The tool is to be used only for its prescribed
purpose. Any other use is deemed to be a case of misuse.
FILLING BAR AND CHAIN LUBRICANT
WARNING:
Do not smoke or bring any fire or flame
near the oil or the chain saw. Oil may spill and cause
a fire.
NOTICE:
The chain saw is not filled with oil at the time of
purchase. It is essential to fill the tank with oil before use.
The chain is automatically lubricated with chain oil during
operation.

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Cs1600e

Tabla de contenido