Cleaning The Mower - Ego Power+ LM2020E Manual Del Operador

3. Hold both the bail switch and the self-propel trigger
simultaneously against the handle with your right
hand and use your left hand to adjust the self-propel
speed-control lever to choose a proper speed.
WARNING:
To reduce the risk of injury, never attempt
to override the operation of the switch or self propel
system. Use the self propel for its intended purpose only.
LED HEADLIGHTS (Fig. A-13)
Press the switch button (Fig. C-22) to turn on/off the LED
headlights in the front of the battery compartment.
POWER INDICATOR ON THE MOWER (Fig. U)
The mower is equipped with a power indicator to indicate
the charge level of the battery pack and the working status
of the mower. The power indicator will illuminate when the
blade is rotating or when the LED headlights are turned on.
Power
Indicator Meaning
on Mower
Mower is working
Shining properly; battery
green has at least 15%
of its charge
Shining red Low battery
The battery is
Flashing red
nearly depleted
The mower or the
Shining
battery pack is
orange
overheated
Flashing The mower is
orange overloaded
MOWER OVERLOAD PROTECTION
To prevent overload conditions, do not try to remove too
much grass at one time. Slow down your cutting pace or
raise the cut height.
Your mower has built-in overload circuit protection. When
the mower is overloaded, the motor will stop and the
power indicator on the mower will flash orange. Remove
the battery pack from the mower. Check to see if grass
has collected beneath the deck and clear it if necessary,
then install the battery and restart the mower.
BATTERY HIGH TEMPERATURE PROTECTION
The battery pack will generate heat during operation. The
56 VOLT LITHIUM-ION CORDLESS MOWER — LM2020E / LM2020E-SP
heat dissipates more slowly in hot weather. If the battery
temperature exceeds 70°C during operation, the protection
circuit will immediately turn off the mower to protect the
battery pack from damage. The power indicator on the mower
will shine orange and the LED on the battery will flash orange.
Release the bail handle, wait until the battery pack cools down
to approximately 67°C , then restart the mower.
MAINTENANCE
remove the safety key and battery pack from the mower
before cleaning or performing any maintenance.
replacement parts. Use of any other parts may create a
hazard or cause product damage. To ensure safety and
reliability, all repairs should be performed by a qualified
service technician.
Action

CLEANING THE MOWER

N/A
battery pack when servicing or transporting the mower.
The underside of mower deck should be cleaned after each
Stop the mower and
use, as grass clippings, leaves, dirt and other debris will
charge the battery pack
accumulate. This accumulation is undesirable, as it will
promote rust and corrosion on metal parts and reduce the
Stop the mower and
cutting efficiency of the mower.
charge the battery pack
Remove any build-up of grass and leaves on or around the
Remove the battery
drive shaft (LM2020E-SP) and the motor fan (do not use
from the mower, move
water). Wipe the mower clean with a damp cloth.
them to the shade and
cool them at least 15
REMOVING/INSTALLING THE BLADE
minutes
Slow down your pace
or raise up the cut
heavy gloves or wrapping the cutting edges with rags or
height to decrease
other materials when performing any maintenance on the
the load
mower blade.
◾
To Remove the Blade (Fig. W)
NOTICE: If the bolt rotates with the motor shaft when
loosening the bolt, turn the fan by hand to align the
through holes in the fan with the holes in the blade,
and place another metal rod into the aligned holes.
◾
To Install the Blade
Following the assembly sequence in Fig. V, with the fan
blade towards deck and the printed blade side towards
outside, align the through holes in the fan with the
holes in the blade (Fig. X) and then tighten the blade as
Fig. X shown.
WARNING:
To avoid serious personal injury, always
WARNING:
When servicing, use only identical
WARNING:
Always remove the safety key and
WARNING:
Always protect your hands by wearing
EN
15