English - IKEA GALANT Manual Del Usuario

ENGLISH

Advice and instructions for GALANT. hand control.
— Manufacturer: ROL Ergo AB, Lidtorps- — The table is now ready for use. The
vägen 12 S-556 28 motors stop automatically when the table
reaches its lowest and highest position
— Jönköping, Sweden.
— Tripod type: RE-046/047 respectively.
— Protection class: IP20
— Weight: 33 kg Usage of the table
— Sound level: lower than 70 dB(A) The table can only be used as a working
— Height setting interval: 68-118 cm (with table with the possibility to continuously
spacing sleeves 73-123 cm) adjust working height between sitting and
— Maximum load: 80 kg
standing position. The table can only be
— Temperature interval at usage: +5 up to used indoors and in dry premises (office
+40 degrees C
environment or similar). Lowest height from
— Temperature interval at storage: -10 up floor to the upper edge of the table top is
to +50 degrees C approx. 68 cm and the highest height is 118
cm. If a spacing sleeve is mounted on the
Humidity: 20% up to 80% at +30 degrees legs these measurements are increased by
C. 5 cm.
The table must not be overloaded - maxi-
Every person who is responsible for this mum load is 80 kg. The motors may be run
table at installation or employment of the continuously for maximum 2 minutes. After-
table in daily use or in service and repair ward, the motors must stand by for approx.
18 minutes before they can be used again.
work should carefully read these instruc-
tions. Keep these instructions in the plastic
pocket enclosed with your sit/stand table. 1 Follow these instructions when adjusting
table height:
Installation instructions:
— The table is assembled according to
separate assembly instructions. 2 Insert the safety key in the socket on the
— For correct combination of table top hand control.
and tripod size - see assembly instructions. 3 Make sure no objects are in the way of
the table adjusting height freely.
— Connect the plugs from the motors in
the two table legs to the sockets on the
command box. In a similar way, connect In order to run the table up/down, press the
the plug from the hand control. Place the manoeuvre button with an arrow pointing
electrical cables so that they do not get up and down respectively.
damaged. See assembly instructions. Ca-
bles from the motors and the hand control When the table is left unattended, the
should be attached to the frame with the safety key must be removed from the hand
enclosed cable tape. control and placed out of children's reach.
— Connect the electrical cable to a wall
socket. NB! The electrical cable must have Safety regulations
full mobility. When the table is run up/down there may
— Insert the safety key in the socket on the be a risk of getting squeezed. Consider the
4 4
following:
— It is easy to get squeezed between
the moving table top and fixed objects in
the surrounding area. Necessary safety
distance depends on what risk of getting
squeezed is considered greatest - from fin-
ger min. 3 cm to e.g. body/head of a child
min. 40 cm.
— When the table is run up/down the user
shall keep watch so that nobody is injured
or no object is damaged. The table top
must not bump into a fixed object so that
the table is overturned. Always remove
any office chair before the table is run up/
down.
— When the table is left unattended, the
safety key must be removed from the hand
control and placed out of reach of children.
— The table tripod must not be altered or
reconstructed in any way. In service and
repair work of the table, the electrical cable
should always be disconnected from the
wall socket.
Alterations to the control box are absolutely
forbidden!
The table must not be used as a hoisting
device for persons.
Maintenance and repair instructions
After approx. 1 week of use, check that the
screws mounted after delivery are properly
tightened. If the table can not be lowered
or raised, the connections to the command
box and wall socket should be checked as
well as if the safety key is properly inserted
in the hand control. On the hand control
there is a green control light. If this shines
when any of the two manoeuvre buttons
are pressed, there is power leading to the
command box, and conversely, if the green
light does not shine there is no power lead-
ing to the command box. If any part of the
5 5
electrical system is replaced, the system
must be reset as follows:
Run the table to its lowest position by press-
ing the manoeuvre button with an arrow
pointing down. Release the button after-
wards. Press, within 10 seconds, once again
the same button and hold it for at least 5
seconds. The table is now ready for use. If
the table still does not work, please contact
your nearest IKEA store.