Safety Harness; Bumper Bar; Parking Brake - Chicco StyleGo Manual Del Usuario

rts 7. Insert the legrest supports in the lower part of the lining (fig. 7).
ce. 8. To finish fitting the seat lining attach the fabric to the 4 buttons
bri- on the back of the backrest (fig. 8), and the two buttons on the
sides of the seat (fig. 8A).
To remove the lining, follow the same steps in reverse order.
WARNING: After removal of the safety harness (e.g. for wash-
ng ing), ensure that the harness is reassembled correctly using the
act anchorage points. The harness must be re adjusted. To make
sure the harness straps are
ng fitted correctly (on the rear surface of the seat), place your child
inside, fasten the straps and then pull the ends of the straps
firmly.
COMFORT KIT
The Comfort Kit comprises 2 padded shoulder straps and a
crotch strap.
9. Insert the shoulder pads on the straps and insert the buckle
in the padded crotch strap (fig. 9).

SAFETY HARNESS

10. The stroller comes with a five-point safety harness which
consists of two shoulder straps, a waist strap and a crotch
strap with buckle.
WARNING: when using with children aged 0 to 6 months, you
may have to shorten the length of the straps to adjust them to
ut- your baby; to do so, firstly pass the shoulder straps through the
ntil two adjustment slots (fig. 10).
11. Make sure the shoulder straps are at a suitable height for
ear your child. Adjust if necessary (fig. 11).
he 12. After placing your child in the stroller insert the two forks in
the buckle (fig. 12) and adjust the width of the waist belt if
cir- necessary by pressing on the buckles. To unfasten the waist
of belt press the two lateral forks at the same time (fig. 12A).
WARNING: The use of the crotch strap, waist strap and safety
of
harness is necessary to guarantee the safety of your child.
WARNING: After removing the safety harness (e.g. to wash it),
he
ensure that the harness is reassembled correctly using the an-
ear chorage points. The harness must be re adjusted.
her

BUMPER BAR

ha- 13. The seat is equipped with a bumper bar. To attach the bar
insert it in the terminals of the armrests (fig. 13) and check
els that it is firmly in place by pulling it towards you. To remove
ds. the bumper bar press the two buttons on the inside as
hat shown in figure 13A and extract it from the armrests. You
ure can undo just one side of the bumper bar to seat your child.
do The bumper bar can be used both forward facing and par-
ent facing.
WARNING: Always fasten your child with the safety harnesses.
The bar IS NOT a device for restraining your child.
WARNING: The bar must not be used to lift the product with
in the child inside.
en
FITTING THE SEAT ON THE STROLLER
de.
to 14. To attach the stroller seat, insert it in the relevant vertical
To fastening devices until you hear the click which confirms
ack that it has been fastened (fig. 14). To make it easier to attach
the seat to the stroller there are arrows on the sides of the
as- seat showing you the correct alignment of the seat with the
r. fasteners (fig. 14A). The seat can be assembled both forward
facing (fig. 14B) and parent facing (fig. 14C).
WARNING: Before using, make sure that the seat is properly
he locked on by pulling it upwards.
WARNING: If it is not properly locked, press both white keys on
. 5.
ap the fitting devices of the structure and repeat the fitting pro-
he cedure checking that it is completely locked. Contact Chicco
in customer service if you have any problems.
15. To remove the seat press the two armrest buttons at the
same time (fig. 15) and lift.
WARNING: Do not remove/attach the seat when your child is
sitting in it.
HOW TO ADJUST THE BACKREST
16. Press the button on the back of the stroller backrest to re-
cline it to the desired position (fig. 16). Release the button
and the backrest will click into the closest lock position.
WARNING: These operations may be more difficult if your
child is leaning on the backrest.
HOW TO ADJUST THE LEGREST
17. The legrest has two positions. To adjust it, use the buttons
under the legrest (fig. 17).
HAND GRIP
18. Press the round buttons to the side of the handgrip to ro-
tate it to the required position, adapting it to the height
and most comfortable position of the user (fig. 18). The
handgrip can be adjusted to 3 different positions (fig. 18A).
WARNING: never use the hand grip to lift the stroller with the
child inside.
HOOD
19. The stroller is equipped with a sun canopy and windshield
that can be adjusted to various positions. The seat features
two rails positioned behind the armrests to which the can-
opy can be attached.
To fix the canopy to the stroller insert the specific fasteners in
the rails at the side of the seat (fig. 19). To finish fitting the cano-
py to the seat, fasten the back of the canopy on the back of the
stroller backrest using the relevant buttons (fig 19 A). To open
the canopy, push the front arch forward (fig. 19B). Once fas-
tened to the seat, the canopy can be used in the forward facing
or parent facing position without having to remove it. The hood
has a rear opening so you can check on your child. To open it,
lift the fabric flap at the top of the hood (fig. 19C). To make sure
your child is even more protected it is possible to increase the
surface of the hood by opening the zip between the flaps (fig.
19D-19E). To take off the canopy remove the fastening device
from the rails and undo the buttons.
WARNING: The hood must be fixed on both sides of the stroll-
er. Ensure that the hood is correctly secured in position.

PARKING BRAKE

20. The parking brake acts on both of the stroller's rear wheels at
the same time. To activate the braking system push down on
one of the two levers. (fig. 20).
WARNING: Always apply the brakes when the stroller is sta-
tionary. Never leave the stroller on a sloping surface with your
child inside it, even if the parking brake is engaged.
WARNING: After pressing down on the the brake lever, make
sure the brakes are properly engaged on both rear wheels.
SWIVEL WHEELS
21. The stroller has front swivel/fixed wheels. It is advisable to
use the wheels in the fixed mode on particularly changea-
ble surfaces. Use the wheels in swivel mode on normal road
surfaces to have greater control over the stroller.
To use the front wheels in swivel mode, push the side lever
down as shown in fig. 21. To block the front wheels position
the lever as shown in figure 21A. When the stroller is moved
the wheels will lock in the straight position, regardless of the
position they are in.
FOLDING THE STROLLER
WARNING: When carrying out this operation make sure that
your child and other children are at a safe distance. Make sure
13