Range Of Application; Operation; Servicing And Maintenance; Performance - ESAB SAVAGE A40 Manual Del Usuario

Ocultar thumbs Ver también para SAVAGE A40:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 88
Inserting and removing a new protection lens:
To insert the new outer protection ➃ lens the filter must be
removed by unscrewing the two retaining screws ➇ from
the inside of the helmet ➀. The old protection lens can then
be removed and the new lens inserted followed by the light
seal cradle ➅, ADF ➆, inner protection lens ➄ and then the
ADF retaining frame ➇ and finally replace the two retaining
screws (see drawing 2).

Range of application

The SAVAGE A40 welding helmets can be used for the fol-
lowing applications:
Electrode
MIG
Mag
TIG (>=5A)
They are not suitable for use with laser systems and oxy-
acetylene (gas welding) applications. The welding filter must
not be used for any other purpose other than welding. They
should never be used as sunglasses when driving as this
could lead to incorrect identification of the color of traffic
light.
The welding filters operate well under extreme low lighting
and very strong sunlight.

Operation

Adjustment of headgear:
SAVAGE A40 welding helmets are equipped with a comfort-
able headgear that can be adjusted in three different ways.
Push and Move 'Head Height'

Servicing and maintenance

SAVAGE A40 welding helmets should not be dropped. Do
not place heavy objects or tools (hammers etc.) on or inside
the helmet so as not to damage the electro-optical filter.
Drawing 2
Longitudinal Adjustment
Rake Adjustment
Push and Turn
'Head Size'
Drawing 3
Always make sure that the helmet is equipped with an
outside and inner lens (in front of the filter on the outside
and on the inside behind the filter). These protection lenses
must be replaced if damaged in any way (see overleaf ).
They are consumables and should checked and replaced
regularly.
The filter should be cleaned when changing the protection
lenses.
This can be done by any of the following ways:
Wipe with a clean, dry piece of cloth.
Clean with a piece of smooth cloth moistened with
pure alcohol.
Clean with a commercial disinfectant
If used properly the welding filter requires no
further maintenance during its lifetime.
If a filter should be replaced on a SAVAGE A40 welding
helmet, use exclusively certified products (DIN-CE marks).
We recommend the use of ESAB welding filters in all SAVAGE
A40 helmets.
The filter itself contains no special or toxic products and can
be disposed of in the same way as other electronic devices.

Performance

To allow the filter to switch both sensors on the front of the
filter must not be covered, the filter then switches to the
dark state when the arc strikes and to the clear state when it
stops. The filter switches to the light state when the welding
arc stops.

How to set the shade

On the SAVAGE A40 set the shade by turning the knob on
the outside of the helmet (pos. 1).
The most suitable setting can be found on the Chart in this
brochure or chosen using your experience. This setting can
also be made manually during the welding process.
Turning clockwise =darker
Turning anti clockwise = clearer

Switching Grind mode / Welding mode

On the SAVAGE A40 exchange the Welding and Grind mode
by pressing the knob on the shade knob outside of the
helmet.
On Welding mode, by pressing the knob and hold for 2
seconds. The mode will be changed from Welding to Grind.
The green Grind light will flash (pos.4)
On Grind mode, By Pressing the knob and hold for 2 sec-
onds. The mode will be changed from Grind to Welding. The
green Grind light will stop flashing (pos.4)
2
Drawing 4

Publicidad

Tabla de contenido
loading

Tabla de contenido