Operating Voltage; Operating Time - THOMSON WHP3001BK Instrucciones De Uso

Ocultar thumbs Ver también para WHP3001BK:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 10
Operating Instructions
Thank you for choosing a Thomson product.
Take your time and read the following instructions and information
completely. Please keep these instructions in a safe place for
future reference. If you sell the device, please pass these operating
instructions on to the new owner.
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to draw
your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or
important notes.
2. Controls and displays, Fig. 1+3
1.
Charge status LED indicator (green)
2.
Power/signal LED indicator (red)
3.
Power button
4.
Volume control
5.
Auto-Tune button
6.
Frequency channel switch
7.
Power LED indicator (green)
3. Package contents
• 1 WHP3001BK UHF wireless headphones
• 1 transmitter with charging station
• 2 NiMH AAA batteries
• 1 power supply unit
• 1 audio adapter cable, RCA stereo to 3.5 mm jack
• 1 jack adapter 6.3 mm/3.5 mm
4. Safety Notes
Warning
• Using this product limits your perception of ambient noise.
For this reason, do not operate any vehicles or machines
while using this product.
• Always keep the volume at a reasonable
level. Loud volumes, even over short
periods, can cause hearing loss.
• Never open, damage or swallow batteries or allow them to
enter the environment. They can contain toxic, environmentally
unfriendly heavy metals.
• Do not tamper with or damage/heat/disassemble the batteries/
rechargeable batteries.
• The product is intended for private, non-commercial use only.
• Use the product for its intended purpose only.
• Children should be supervised to ensure that they do not play
with the device.
• Do not use the product in areas where the use of electronic
devices is not permitted.
• Only connect the product to a socket that has been approved for
the device. The socket must be installed close to the product and
easily accessible.
2
• Disconnect the product from the network using the power button
– if this is not available, unplug the power cord from the socket.
• Lay all cables so that they do not pose a tripping hazard.
• Do not bend or crush the cable.
• Do not drop the product and do not expose it to any major shocks.
• Dispose of packaging material immediately according to locally
applicable regulations.
• Do not modify the product in any way. Doing so voids the warranty.
• Do not use the product if the adapter, connection cable or power
cable is damaged.
• Do not attempt to service or repair the product yourself. Leave
any and all service work to qualified experts.
• Do not open the device or continue to operate it if it becomes
damaged.
• The batteries and charging station included in the delivery go
together and should always be used in combination.
5. Technical specifications
Transmitting mode
Frequency band(s)
Maximum radio-frequency
power transmitted

Operating voltage

Frequency range
Distortion
Signal-to-noise ratio
Range

Operating time

6. Installing the transmitter/charging station, Fig. 3
• Connect the power supply to the power socket on the rear side
of the transmitter.
• Connect the power supply to a mains socket.
• Connect the RCA plugs of the audio adapter cable to the RCA
sockets on the rear side of the transmitter. Connect the other
end (jack plug) to the headphone jack of your audio source
(television, hi-fi system, DVD player, MP3 player, etc.).
• The red LED (2) lights up.
7. Installing the receiver/headphones, Fig. 2
• Carefully pull off the earpad on the right-hand side.
• Insert the two batteries supplied, making sure you observe
correct polarity.
• Reinsert the earpad until it audibly clicks into place.
8. Getting started
• Switch on the audio source connected to the transmitter (TV or
audio player).
• Switch on the headphones by pressing the Power button (3). The
LED (7) of the headphones lights up green. Make sure that the
red LED (2) is lit. This confirms that the rechargeable batteries
are charged.
UHF stereo
863.53 – 864.53 MHz
< 5 dBm
Transmitter: 8 V, 70 mA
Receiver: 2.4 V,
(2 x 1.2 V NiMH AAA)
20 Hz – 20 KHz
< 2%
> 54 dB
100 m max. (outdoors)
20–30 m (indoors)
8 hrs (at medium volume)

Hide quick links:

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Whp3001bk-uk0013195700131958

Tabla de contenido