Operation And Maintenance; Technical Parameters - GRAPHITE 58G032 Instrucciones De Uso

Do not charge the battery for more than 8 hours. Exceeding this
time limit may cause damage to battery cells. The charger does
not turn off automatically when the battery is full. Green diode
on the charger will remain on. Battery level indication diodes turn
off after some time. Disconnect power supply before removing
the battery from the charger socket. Avoid consecutive short
chargings. Do not charge the battery after short use of the tool.
Significant decrease of the period between chargings indicates
the battery is worn out and should be replaced.
Batteries heat up when charging. Do not operate just after
charging – wait for the battery to cool down to room temperature.
It will prevent battery damage.
BATTERY LEVEL INDICATION
The battery is equipped with battery level indicator (3 LED diodes)
(13). To check battery level status, press the button for battery level
indication (12) (fig. C). When all diodes are lit, the battery level is
high. When 2 diodes are on, the battery is partially discharged.
When only one diode is lit, the battery is discharged and must be
recharged.
ADJUSTABLE MAIN HANDLE
Before starting operation you can adjust main handle to the
position most comfortable for the task. The handle can be set up in 3
positions by turning it 90° left or right from the basic position.
When changing position of the main handle make sure not to
press the switch button, since this blocks rotation of the handle.
• Press the main handle lock button (5) (fig. D).
• Turn the main handle to desired position.
• The main handle automatically locks in the position.
OPERATION / SETTINGS
SWITCHING ON – SWITCHING OFF
Remove blade bar shield and install battery before switching on.
The hedge trimmer features safe switch that requires both hands
to activate.
Switching on – press the switch lock button (4) and hold, then press
the switch button (6) (fig. E).
Switching off – release pressure on the switch button (6) or the
switch lock button (4).
The hedge trimmer will start only when you simultaneously press
the switch lock button (4) with one hand, and the switch (6) with
the other. When one of the buttons is released, the hedge trimmer
stops. Safety brake of the blade will stop the blade in less than 1
second after the switch is released.
INSTRUCTIONS REGARDING SAFE USE
Before starting to work, carefully check the hedge against
invisible objects, such as fence, mesh etc.
• When trimming long branches perform the work gradually, by
layers.
• Operate the hedge trimmer only when the hedge is dry.
• After the work is finished put the blade bar shield on (fig. F).
TRIMMING HEDGES
• Besides trimming hedges, the hedge trimmer can also be used to
trim bushes and shrubs.
• The best results can be achieved when guiding the blade bar so it
is at an angle of approx. 15° with respect to the hedge.
• Two sided blade and counter-moving cutting parts allow cutting
in both directions or swinging motion (fig. G).
• To obtain uniform height of a hedge, it is recommended to
extend a rope or a line along trimmed hedge plane. Cut branches
protruding above the defined line (fig. H).
• To guide the branches into the blade, move the blade bar evenly
forward or backward along the line of cutting.
• Perform hedge sides trimming in arc motions, from bottom
upwards (fig. I).

OPERATION AND MAINTENANCE

Remove the battery from the device before commencing
any activities related to installation, adjustment, repair or
maintenance.
Exercise caution due to sharp edges of cutting blades. When not
in use, the blade bar should always be protected with the blade
shield.
MAINTENANCE AND STORAGE
• Cleaning the device immediately after each use is recommended.
• If possible, motor casing should be always free from dust and dirt.
• Wipe the device with a clean cloth or blow through with
compressed air at low pressure.
• Do not use any cleaning agents or solvents, they may damage
plastic parts.
• Be careful to avoid ingress of water into the device.
• Check the hedge trimmer against obvious damages, such as
loosened or damaged blade, loose screw joints and worn out or
damaged structural parts.
• Make sure that guards and protection parts are not damaged and
installed properly. Carry out all necessary maintenance and repair
works before using the hedge trimmer.
• Clean the blade bar and spray maintenance liquid on it after each
use. When operating the tool for a long time, it is recommended to
regularly lubricate the blade with thin layer of oil (fig. J).
• Check condition of blade edges.
• Use only original equipment and original spare parts.
• Store the hedge trimmer in a safe, dry place, beyond reach of
children.
• Do not put any objects on the hedge trimmer body.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized by
the manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS
Cordless Hedge Trimmer 58G032
Parameter
Battery voltage
No load blade speed
Cutting width
Blade bar length
Max. cutting thickness
Protection class
Weight
Year of production
58G032 defines type and indication of the device
14
Value
18 V DC
1300 min -1
510 mm
570 mm
15 mm
III
2,2 kg
2019