Installation Instructions; Symbol Description; Flow Diagram; Technical Data - Hansgrohe Raindance Showerpipe 27145000 Modo De Empleo/Instrucciones De Montaje


Safety Notes
Gloves should be worn during installation to prevent crushing and cutting

injuries.
The arm of the shower head is intended only to hold the shower head. Do not

load it down with other objects!
Children as well as adults with physical, mental and/or sensoric impairments

must not use this shower system without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from using this shower system.
Do not allow the streams of the shower touch sensitive body parts (such as your

eyes). An adequate distance must be kept between the shower and you.
The product may not be used as a holding handle. A separate handle must be

installed.
The shower system may only be used for bathing, hygienic and body cleansing

purposes.
The hot and cold supplies must be of equal pressures.


Installation Instructions

• The fitting must be installed, flushed and tested after the valid norms.
• The filter insert (A) must be used to ensure the standard flow rate and to protect
the hand shower against incoming dirt by pipework. Do you want a larger water
flow rate, then you must use the filter packing (B) instead of the filter insert (A).
Incoming dirt leads to defects or/and can damage parts of the hand shower;
such caused faults voids all liability and guarantee claims.
• In case of emergencies, the lower part of the pipe can be shortened by means of
a fine saw.

Technical Data

Operating pressure:
Recommended operating pressure:
Test pressure:
(1 MPa = 10 bar = 147 PSI)
Hot water temperature:
Recommended hot water temp.:
Connections:
anti-pollution function
Fault
Insufficient water
Crossflow, hot water being forced into cold water
pipe, or vice versa, when mixer is closed
Spout temperature does not correspond with
temperature set
Temperature regulation not possible
Safety stop button not operating
Diverter stiff
Diverter leaking
4
max. 1 MPa
0,25 – 0,5 MPa
1,6 MPa
max. 80°C
65°C
cold right - hot left
Cause
- Supply pressure inadequate
- Regulator filter dirty
- Shower filter seal dirty
- Backflow preventers dirty or leaking
- Thermostat has not been adjusted
- Hot water temperature too low
- Temperature regulator dirty or calcified
- For new installations: basic body incorrectly
connected (should be: cold right, hot left) or installed
with 180º rotation
- Spring defective
- Button calcified
- Cartridge defective
- Dirt or sedimentation on valve seat, shut-off unit
damaged
Assembly see page 31
English

Symbol description

Do not use silicone containing acetic acid!
Safety Function (see page 33)
The desired maximum temperature for example max. 42º C can be pre-
set thanks to the safety function.
Adjustment (see page 33)
After the installation, the output temperature of the thermostat must be
checked. A correction is necessary if the temperature measured at the
output differs from the temperature set on the thermostat.
Dimensions (see page 34)

Flow diagram

(see page 34)

overhead shower

hand shower

overhead shower + hand shower
Operation (see page 35)
Maintenance (see page 36)
The non return valves must be checked regularly according to DIN EN
1717 in accordance with national or regional regulations (at least once
a year).
To guarantee the smooth running of the thermostat, it is necessary from
time to time to turn the thermostat from total hot to total cold.
Cleaning (see page 37)
enclosed brochure
Spare parts (see page 39)
Test certificate (see page 35)
Remedy
- Check water pressure (If a pump has been installed
check to see if the pump is working).
- Clean filters
- Clean filter seal between shower and hose
- Clean backflow preventers, exchange if necessary
- Adjust thermostat
- Increase hot water temperature to 42 ºC to 65 ºC
- Clean temperature regulator, exchange if necessary
- Install function block turned through 180º
- Clean spring and/or button, exchange if necessary
- Clean spring and/or button, exchange if necessary
- Clean valve seat or exchange diverter