Programming - Nice mindy TT1V Instrucciones Y Advertencias Para El Instalador

2.1.3) Weather sensors
The control unit manages the climatic sensors by means of a "VOLO
S RADIO"-type radio (max. no. 3). Memorisation of a "VOLO S
RADIO" sensor must be carried out like that of a normal transmitter.
Follow the procedure set out in Table "A2". Intervention levels must
be programmed actually on the "VOLO S RADIO" sensor.

3) Programming

Each transmitter or radio sensor is recognised by the control unit by
means of an unequivocal "code". A "memorisation" phase must
therefore be performed in order to allow the control unit to recognise
each single transmitter.
!
• All the memorisation sequences are timed, that is, they
must be completed within the programmed time limits.
When the memory contains no codes the first radio control unit can be entered as follows:
Table "A1" Memorizing the first transmitter (fig. 13)
1. As soon as the control unit is powered, 2 long beeps will sound
2. Within 5 seconds press and hold down button
(for approx. 3 seconds)
3. Release button
N.B. If transmitters have already been memorised in the control unit, 2 short beeps will be heard when it is switched on. This means that
the above procedure is not valid and another memorisation procedure must be used (Table "A2").
When one or more transmitters have already been memorised, others may be enabled as follows:
Table "A2" Memorizing the first transmitter (fig. 14)
1. Press and hold down button
(after about 5 seconds) then release it
2. Press button
3. Press button
N.B. 3 long beeps will sound if memorisation has been successfully completed. 6 beeps will sound when the memory is full (30
transmitters), telling you the transmitter cannot be memorised.
If you need to delete all the data contained in the memory of the
control unit, carry out the following procedure.
The memory can be deleted:
• using a non-memorised transmitter starting from point A.
• using a previously memorised transmitter starting the procedure
from point N. 1
Table "A3" Memory deletion (fig. 15)
A Switch the control unit off and cut the jumper on the weld side of the card (see fig. 15).
B Power the control unit and wait for the initial beeps
1 Press and hold down button
(after about 5 seconds) then release it.
2 Press and hold down button
release button
3 TPress and hold down button
release button
4 Press and hold down button
release button
5 If you wish to delete all the data in the memory, press the
within 2 seconds until you hear the first of 5 beeps, then release them.
N.B. 5 beeps will sound, indicating that all the codes in the memory have been deleted.
when you hear the first of the 3 beeps confirming memorisation
of the new transmitter until you hear a beep
of a previously memorized transmitter slowly 3 times
on the new transmitter again, releasing it when you hear the first of the 3 beeps.
of a previously memorized transmitter until you hear a beep
of the transmitter until you hear 3 beeps;
exactly during the third beep.
of the transmitter until you hear 3 beeps;
exactly during the third beep.
of the transmitter until you hear 3 beeps;
exactly during the third beep.
Wind intervention levels must be given priority, followed by the rain and
sun. Please refer to the "VOLO S RADIO" manual for further details.
!
interventions on the anemometer provoke a command
equivalent to the key command on the transmitters
• For transmitters with multiple "groups", choose the group
the motor must be associated with before proceeding with
the memorisation phase.
• Programming via radio may be done on all the control units
within the range of the transmitter; therefore, only the one
involved in the operation should be kept switched on.
of the transmitter to be memorised
You can delete:
• the transmitters only, by stopping at point 4 of the procedure;
• all the data (transmitters and programming the working time), by
carrying out the procedure through to point 5.
keys simultaneously
Example
3s
Example
New 5s
Old X3
New
Example
5s
3
GB