Benning DUSPOL expert Manual De Instrucciones página 8

is done by means of two built-in micro batteries (LR03/
AAA). Battery replacement is necessary as soon as illu-
mination does not work anymore. In this case, the battery
voltage is below 2.2 V.
How to replace the batteries:
Take a screw driver
compartment (next
¼-turn in direction of the arrow (counter-clockwise). The
slot is now vertical and the battery compartment with the
batteries can be removed.
Remove the discharged batteries from the battery
compartment. Insert the new batteries with correct
polarity (see marking) into the battery compartment. Put
the battery compartment with the batteries back onto the
handle and lock it by ¼-turn in clockwise direction (slot
must be horizontal and the marking points are opposite!).
Make sure not to damage the O ring (art.-no. 772897). If
necessary, it has to be replaced.
Battery disposal:
Do not dispose of batteries with the household garbage.
You can return used batteries to public collection facilities
in your community area or return them to any retail outlet
selling similar batteries.
9. Technical data:
- Guideline: IEC 61243-3, voltage class B (AC 1000 V/
DC 1500 V)
- Over voltage category: CAT IV 500 V, CAT III 690 V
- Protection class: IP 64, IEC 60529 (DIN 40050)
IP 64 means: Protection against access to dangerous
parts and protection against solid impurities,
dustproof, (6 - first index). Splash proof, (4 - second
index). Can also be used in case of precipitation.
- Nominal voltage range: 12 V to AC 690 V/ DC 750 V
- Internal resistance, measuring circuit:
- Internal resistance, load circuit – both push buttons
actuated!: approx. 3.7 kΩ...(150 kΩ)
- Current consumption, measuring circuit:
max. I 3.5 mA (690 V) AC/ 3.4 mA (750 V) DC
n
- Current consumption, load circuit - both push buttons
actuated!: I 0.2 A (750 V)
s
- Polarity indication: LED +; LED -
- Indicating steps LED: 12 V+*, 12 V-*, 24 V+, 24 V-,
50 V, 120 V, 230 V, 400 V and 690 V (*: only with both
push buttons actuated)
- max. indicating errors: U
- Nominal frequency range f: 0 to 500 Hz
- Phase and phase-sequence indication: ≥ U
50/ 60 Hz
- Vibrating motor, starting: ≥ U
- max. permissible operating time: ED = 30 s (max. 30
seconds), 240 s pause
- Test current, continuity check: max. 2 μA
- Testing range, conducting resistance: 0 - 108 kΩ,
- Sound level acoustic signal: 55 dB
- Battery: 2 x Micro, LR03/ AAA
- Weight: approx. 200 g
- Connecting cable length: approx. 900 mm
- Operating and storing temperature range: -10 °C to
+55 °C (climate category N)
- Relative air humidity: 20 % to 96 % (climate category N)
- Reverse control times (thermal protection):
voltage/ time: 230 V/ 30 s, 400 V/ 9 s, 750 V/ 2 s
Attention!
The phase-sequence indication, measuring point
illumination and continuity check do not work anymore, if
the batteries are empty! Remove the batteries if not using
the voltage tester for a longer period of time!
10. General maintenance:
Clean the exterior of the housing with a clean dry cloth
(exception: special cleansing cloths). Should such
electrolyte contamination or white deposits occur near
the battery or the battery housing, these must also be
removed with a dry cloth.
09/ 2009

and open the
to the cable outlet)
± 15 %, ELV U - 15 %
n
n
230 V
n
11. Environmental notice
At the end of the product's useful life, please
dispose of it at appropriate collection points
provided in your country.
battery
by a
230 V,
n
DUSPOL expert
®

6