Cutting Tips; Service Interval - Milwaukee M18 HUP700 Manual Original

Cutting
Before cutting, ensure blades are properly installed.
1. Guide the cable at right angles to the cutting of the cable cutter.
Do not attempt to make angled cuts as it will damage the
workpiece and blades.
2. Pull and hold the trigger through the operation.
An LED will light when the trigger is pulled.
3. Once cutting has been carried out, or the tool is switched o , let
the release button go again and press the hydraulic reset button
so that the cutting bars open.
NOTE: Workpiece may move slightly during the cut.
Action in the event of faults
• The cable can be broached and become live, in which case always
inform the safety o cer, stop the cutting process, and initiate
suitable protective measures
• Always ensure that the device is and will stay disconnected from
the power supply before approached and touching the device
• press and hold the hydraulic reset button until the cutter opens
completely
GB
• check the battery capacity
• check the material and material thickness against the technical
data
• If it is suspected that a live cable has been cut, the cable-cutter
has to be inspected in an authorized specialist workshop
Jammed Blades
Dirt and debris can cause the blades to become jammed together
after a cut
• Press and hold the hydraulic release button to ensure the tool
has reset.
• Remove the battery pack.
• Follow the picture description to open the cutting bars
• Clean any dirt and debris from the blades before starting another
cut.

Cutting Tips

• Do not attempt to make angled cuts as it will damage the
workpiece and blades.
• Cut clean material to extend the blade life. Wipe dirt and debris
from material and blades before beginning the cut.
WORKING INSTRUCTIONS FOR PUNCHING
Check if the nominal diameter of the matrice is equal to the
nominal size of the stamp.
English
Deutsch
28
MAINTENANCE
Remove the battery pack before starting any adjustment, cleaning
and maintenance work on the device.
Never open the device, removable battery or charger.
Check the device for any problems such as noise or jamming of
moving parts that could be a ecting the device.
The ventilation slots of the device must be kept clear at all times.
To avoid injury and damage, never immerse the device, removable
battery or charger in liquid or allow liquid to penetrate them.
Further service and repair work may only be carried out by authori-
sed specialist workshops.
The device contains hydraulic uid. Hydraulic uids pose a hazard
to groundwater. Uncontrolled draining or improper disposal is
punishable by law.
The next service deadline is indicated by LED on the device.
Return the tool, battery pack, and charger to a MILWAUKEE service
facility for repair. After six months to one year, depending on use,
return the tool, battery pack and charger to a MILWAUKEE service
facility for inspection. Use only Milwaukee accessories and Milwau-
kee spare parts. Should components need to be replaced which
have not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If the tool does not start or operate at full power with a fully char-
ged battery pack, clean the contacts on the battery pack. If the tool
still does not work properly, return the tool, charger and battery
pack, to a MILWAUKEE service facility for repairs.

Service Interval

Refer to the ONE-KEY App for information regarding necessary ser-
vicing, such as uid replacement. Return the tool to a MILWAUKEE
service facility for all repairs and maintenance.
NOTE: The week and year of tool manufacture may be
needed. This information can be found on the serial number
located on the tool nameplate.
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
For safe shipping, we recommend packing the hydraulic pump in a
sealed, oil resistant plastic bag and using the original packaging.
ONE KEY™
To learn more about the ONE-KEY functionality of this device,
please refer to the Quick Start guide included with this product or
go to http://www.milwaukeetool.com/one-key
To download the ONE-KEY app, visit the App Store or Google Play
from your smart device.
We considered the result to be within our minimum acceptable
performance level according to EN 301489-1/ EN 301489-17. And we
will give the operation guidance to the customer in user manual.