Delta Danco 600 Serie Manual De Instrucciones

Removal of Old Trim Figure 1
1. Shut off water supply to tub/shower faucet. This may require shutting of the main water supply to the house or facility.
Once the water supply is shut off, turn on the faucet to allow the water pressure to be released.
2. Remove the index button (A) from the old handle (C). Remove handle screw (B) and handle (C).
3. Note which valve type is being used. (Fig. 2). Note whether the valve uses a diverter (H).
4. Remove dome nut assembly (D). Remove faceplate screws (E). Remove faceplate (F). Slide off body sleeve (G).
A B C
D G
E
FIGURE 1
Correct Valve Identification Figure 2
1. After the old trim has been removed, refer to Fig. 2 to determine correct valve.
Valve Type A 600 Series with #212 Ball uses a stem that is diamond shaped on the end.
Valve Type B 600 Series with #70 Ball uses a stem that is round on the end.
Valve Types A & B operate by rotating the handle up to turn on the water.
Valve Type C Monitor 14 Series uses a stem that is round with two flat sides.
®
Valve Type C operates by turning the handle right to left to turn on the water.
2. Note whether the valve uses a push button diverter to control the water to the shower head.
VALVE TYPE A
600 Series with #212 Ball
shown with diverter
stem
diverter
FIGURE 2
Instructions for Delta
F
H
VALVE TYPE B VALVE TYPE C
Monitor ® 14 Series
600 Series with #70 Ball
shown without diverter shown without diverter
stem
stem
® Universal Trim Kit
Installation of Faceplate Figures 3, 4, 5, 6 & 7
1. Install new sleeve by sliding over valve (Fig. 3).
Note: Valve Type A and Type B use the same sleeve (A).
Valve Type C uses the larger sleeve (B).
2. Install new dome nut (C) and dome bushing (D) (Fig. 4).
(Valve Types A & B ONLY). Hand-tighten only.
Note: Valve Type C does NOT use a dome nut assembly.
Dome bushing can be adjusted if stem is loose.
E
E
F
F
M
M
H1
H1
J
J DIVERTER HOLE Diverter Hole
4. Choose the correct faceplate insert:
Valve Types A & B use the same faceplate insert (F) (Fig. 5)
Valve Type C uses the faceplate insert (G) with the larger
inner opening (Fig. 6).
Using the foam insert (H1 or H2) included (note two
different sizes), remove backing paper and adhere to the
back of the correct faceplate insert. Snap the faceplate
insert (F or G) into the faceplate (E). Firmly press faceplate
insert into faceplate. Note: The tabs on the faceplate insert
will align with slots on the faceplate.
Valve Type C
Valve Type A/B
DELTA-1
Valve Type A/B
A A
B B
FIGURE 3
D
D
L
L
3. Locate the faceplate (E).
If the valve uses a diverter, remove the "O" Ring
(L) on the back of the face plate and remove the
diverter plug (J) (Fig. 5). Using the smaller foam
insert (K), remove the backing paper and adhere to
the back of the faceplate (E) where the diverter will
pass through.
K
K
If diverter is not used, do not remove the diverter
*shown with
diverter
plug and "O" Ring, the diverter foam is not
I
I
FIGURE 5
required and proceed to Step 4.
Valve Type A/B
E
E
M
M
G
G
J
J
5. Place faceplate gasket (L) into the groove on the back of the
faceplate (E). Slide faceplate assembly over the sleeve. Make sure
the diverter hole is toward the bottom (Fig. 7). Press faceplate
assembly against the wall, making sure not to dislodge the faceplate
insert. Secure faceplate assembly to the valve body using included
screws (M). Do not over-tighten.
FIGURE 7
Valve Type C
C
C
FIGURE 4
Valve Type A/B
L
L
H2
H2
FIGURE 6
Valve Type C