Segway Ninebot eKickScooter ZING A6 Manual Del Usuario página 7

6. Specifications
Item Ninebot eKickScooter ZING A6
Weight and Net Weight Approx. 10.1 lbs (4.6 kg)
Size
Length × Width × Height Approx. 25.6 × 12.6 × 33.5 inch (650 × 320 × 850 mm)
Max. Payload 88 lbs (40 kg)
Rider
Recommended Age 6+ yrs.
Requirement
Recommended Height 3'5"–4'7" (105–140 cm)
First-gear speed: 5.0 mph (8 km/h), second-gear speed: 6.2 mph
Speed Mode (Max Speed)
(10 km/h), third-gear speed: 7.5 mph (12 km/h)
Typical range [1] Approx. 3.1 miles (5 km)
Vehicle
Traversable Terrain Flat surface, paved road; obstacles < 0.4 in (1 cm); gaps < 0.4 in (1 cm)
Parameters
Operating Temperature 14–104°F (-10–40°C)
Storage Temperature -4–122°F (-20–50°C); 41–86°F (5–30°C) recommended
IP Rating IPX4
Charging Time Approx. 3 h
Battery Type Lithium-ion battery
Nominal Voltage 10.8 V
Maximum Voltage 12.6 V
Battery
Pack Charging Temperature 32–113°F (0–45°C); 50–95°F (10–35°C) recommended
2500 mAh/27 Wh
Nominal Capacity / Energy
Over-heating, short circuit, over-current and over-charge protection
Battery Management System
Nominal Power 50 W
Motor
Max. Power 80 W (0.08 kW)
Input Voltage 100–240V~
Battery
Rated Output 11.6 V
Charger
Output Power 11.6 W (0.01 kW)
Braking Method Rear-fender brake
Tires Front wheel: PU perfusion, Rear wheel: Rubber solid
Frame Material Steel
Others
7.5 A
Overcurrent protection value
Handlebar Material TPR
[1] Typical range: tested while riding with a full battery, 61 lbs (30 kg) load, 77°F (25°C), 60% of max. speed on
average on pavement.
* For the first ride, the default speed mode is the first-gear mode. When the kickscooter powers off, the speed
mode setting will be kept till the next time you turn it on.
, 1.0 A
11
7. Maintenance
Maintenance should be carried out by an adult regularly.
Cleaning
Use a soft and wet cloth to clean. Stains hard to remove can be scrubbed with a toothbrush and
toothpaste, then wiped o with a soft and wet cloth.
To prevent jamming to the wheels, wheel bearings, or brakes, please clean and check these areas (as
shown in the gray highlighted areas below) for dirt and other foreign objects.
Wheel
bearing
First clean up the foreign objects, and then wipe clean with a soft wet cloth. Lubricate both sides of
the bearing with lubricating oil or machine oil. If the problem still exists, please contact customer
service. CAUTION: To avoid the accumulation of foreign objects, DO NOT ride on muddy, dusty,
grassy or slippery roads. Do NOT clean your kickscooter with alcohol, gasoline, acetone, or other
corrosive/volatile solvents. These substances may damage the appearance and internal structure of
your kickscooter. Do NOT wash your kickscooter with a power washer or hose.
WARNING
● Do not dispose of this product in a landfill, by incineration, or by mixing with household trash.
Serious danger/injury can occur because of the electrical components.
● Before cleaning, Please check to make sure the kickscooter is powered o , the power cord is
unplugged, and the rubber cap on the charging port is tightly sealed; otherwise you may damage
the electrical components.
1
12
2