Owner’s Manual ENGLISH pp. 1-13 ESPAÑOL pág 14-19 Nano-Lite™ Vacuum Cleaner Review this manual before operating the cleaner Contents Important safeguards ..3 Cleaner assembly Carton contents... . . 4 Attach hose .
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a Hoover Sales and Service Center or Authorized Hoover Warranty Service Dealer (Depot).
If you need any assistance: Visit our website at hoover.com. Click on the “Service” button to find the service outlet nearest you OR Call 1-800-944-9200 for an automated referral of authorized service outlet locations (U.S. only) OR Call 1-800-263-6376 to speak with a representative in our Consumer Response Center.
NOTE: The cleaner is shipped with the agitator brush roll in the “BARE FLOOR” position. Before carpet cleaning, step on the pedal (Fig. 2-1, #8) to turn the agitator brush roll to “CARPET”. Position tools Slide the crevice wand (E) down for storage as shown.
The cleaner is shipped with the agi- Handle positions ON-OFF switch tator brush roll in the BARE FLOOR The handle has two positions: Plug cord into electrical outlet. position. To turn the agitator brush upright and operating. To turn cleaner ON (I), push ON/OFF roll on for CARPET, step on the switch once.
Cleaning lightweight Cleaning tools 2-11 flexible rugs Tools allow for cleaning surfaces above the floor and for reaching Stand on one end of rug and move hard to clean areas. cleaner toward other end or edge. Before reaching edge, push down The cleaner is ready for tool use on handle.
3. Maintenance Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness. Hold dirt cup over trash receptacle. How to empty Press dirt cup door release button Press dirt cup release button (B) (C) to open dirt cup door (D).
Página 9
When purchasing a Allow filter to air dry for 24 hours Lay cleaner flat with bottom of new belt, ask for HOOVER belt before replacing filter into cleaner. cleaner facing up as shown. package No. 40201-280 (belt part Reposition filter by inserting under No.
3-12 3-13 3-14 Removing hood Remove 2 screws from bottom plate. Remove 2 screws on agitator cover (B). Lower cleaner base so it is flat on the floor. Remove 2 screws located at back of hood (A). Lift hood off. 3-15 3-16 3-17...
The agitator brush roll is equipped with two ball bearings that should be lubricated periodically by a Hoover Sales and Service Center or The agitator brush roll an Authorized Hoover Warranty Service Dealer. When to replace...
(U.S. Problem: Cleaner/tools won’t pick up only). Problem: Smoky Possible Cause Do not send your cleaner to Hoover Checking airflow path Possible Solution Glenwillow, Ohio for service, 2. Plug cleaner in and turn ON. • Broken or worn belt this will only result in delay.
Página 13
Checking agitator brush roll 9. Turn cleaner OFF and unplug. 10. Remove cleaner hood (Figs. 3-11 through 3-13) and agitator brush roll cover (Figs. 3-14 & 3-15). Look into opening (D), and around liner beneath agitator brush roll (E) and remove any accumulated debris. 11.
Consejo: Adjunte su recibo de compra a este Manual del propietario. Nano-Lite™ Para obtener el servicio de garantía de su producto HOOVER puede requerirse la verificación de la fecha de compra. Asegurese de registrar su producto en linea a Hoover.com...
Si necesita asistencia: superior gira para soltar el cordón Visite nuestra página en Internet con rapidez hoover.com. Haga clic en el botón Haga funcionar la aspiradora Conecte la manguera “Service” para encontrar el centro de solamente con el voltaje especificado servicio más cercano a usted O...
en el cuerpo de la aspiradora, a fin de flexibles “BARE FLOOR” (piso expuesto). almacenar o transportar la aspiradora Párese sobre un extremo de la alfombra con comodidad. Para bajar el mango: y pase la aspiradora hacia el otro 2-13 oprima el botón (B) en la base del extremo o borde.
(B). pliegues para alergenos. Qué comprar Cuando compre un nuevo filtro final, 3-15 pida el paquete de filtro HOOVER No. 40110-013 (No. de pieza del filtro Levante la cubierta del agitador para Oprima la lengüeta (A) ubicada en la 1BEB124710000).
Tire del otro lado del rodillo de escobillas lubricados periódicamente en un Centro funciona del agitador para colocarlo en su lugar. de ventas y servicio de Hoover o por un Concesionario autorizado de servicio de Causa posible garantía de Hoover.
Página 19
1. Revise el nivel de llenado del depósito para polvo; vacíelo si es necesario. Revisión del paso del flujo de aire 2. Enchufe la aspiradora y enciéndala. Revise si hay succión en el extremo de la manguera (A). Si hay succión, continúe con el paso 3.