Publicidad
Idiomas disponibles
Idiomas disponibles
Revolve the cable into the roller gap in the
clockwise direction, 15-2.
Insert the cable adjustable head into the metal
piece, Fig.15-3.
Fasten the screw hat tightly and fix it on the metal
piece, Fig.15-4.
7
Put the motor cover back and use the motor
cover screws to fix it, Fig.16.
8
Use the screws (19) to fix the left/right side
covers (34), (35), Fig.17.
9
Use the screws (32) to install the water bottle
holder (31) on the left upright tube (28), Fig.18.
CALIBRATION.-
Follow the next steps:
1.- With the monitor off, press the ENTER and -
buttons simultaneously.
2.- Move the running belt to turn on the monitor.
Keep the keys pressed until the screen shows "LF
LEVEL" or "RT LEVEL"
3.- Select the right knob "RT LEVEL" or left "LF
LEVEL" with the + or - keys and press ENTER to
calibrate.
4.- The monitor will show you sequentially + R1, +
R2, + R3, + R4, + R5, + R6, + R7, + R8, -R8, -R7, -
R6, -R5, -R4, - R3, -R2, -R1 for the right knob and +
L1, + L2, + L3, + L4, + L5, + L6, + L7, + L8, -L8, -L7,
-L6, -L5, -L4 , -L3, -L2, -L1 for the left knob.
5.- Place the knob in the position indicated by the
monitor and press START / STOP to save the
position and continue to the next point. You can
return to previous points with the + or - keys.
6.- Press ENTER to return to the previous menu and
START / STOP to exit.
Note: Values for the same point are slightly different
for an ascending or descending sequence.
LEVELLING.-
Once the unit has been placed into its final position
for doing exercise, make sure that the treadmill sits
flat on the floor and that it is level.
Place a spirit level on the running belt, Fig.19, and
screw the adjustable feet (160) either in or out to
level up the belt, as shown in Fig.19.
MOVEMENT & STORAGE.-
The unit is equipped with wheels (165), Fig.20, to
make it easier to move. If you wish to move the
treadmill, tilt the treadmill, Fig.20, so that the wheels
(165) rest on the floor.
NOTE: To prevent accidents DO NOT move the
treadmill across uneven floors.
MAINTENANCE.-
Use the bottle of lubricant (156) to lubricate the
sportkoncept
inside of the belt Fig.21, in order to keep your unit in
top condition and to ensure that friction between the
belt and the board is kept to a minimum (due to
different running styles, always apply more
lubrication to the area where you place your feet
during the exercise).
It is advisable to lubricate the base of the belt
between the board and the band every month,
depending on how often it is used.
If the belt starts to slip after lubrication, then check
the tension of the belt. To tension the belt, Fig.22,
take the Allen key 6mm turn screws (R & L) one full
turn in a clockwise direction.
Do not use solvent based lubricants. Do not use
lubricants not supplied by the manufacturer.
ADJUSTING THE BELT.-
If your unit is not seated evenly on the four contact
points, this may cause the belt (X) to shift sideways.
Rigorous quality control adjusts and checks the
running belt. However, due to weight differences
and individual styles of running, the belt may be
prone to shift sideways.
If the belt does shift to the left or right, stop the
machine.
BELT OFFSET TO THE RIGHT
This procedure is very important. Follow these
steps. If the belt has moved to the right, turn screw
(R) on the right-hand side of the machine a 1⁄4 turn
clockwise. Note the position of the belt, if after one
minute the belt is not completely centred then
repeat the operation. If you see that the belt has
moved too far over to the left then turn the right
screw back slightly in an anticlockwise direction
Fig.22.
As soon as you have adjusted the belt you can
begin exercising again.
BELT OFFSET TO THE LEFT
In the event that the belt has moved to the left, turn
screw (L) on the left-hand side of the machine a 1⁄4
turn clockwise. Note the position of the belt, if after
one minute the belt is not completely centred then
repeat the operation.
If you see that the belt has moved too far over to the
right then turn the left screw back slightly in an
anticlockwise direction Fig.22.
Important: Overtightening of the belt can lead to a
loss of speed on the machine and even stretch the
belt itself.
Bear In mind that one turn of the right screw (R) in
a clockwise direction has the same effect on the
position of the belt as one turn of the left screw (L)
in an anticlockwise direction. Consequently, in the
event of excessive belt movement you can use
either of the two screws in order to avoid
overtightening the belt.
21
G689
Publicidad
