Technical Data; Brief Description - Felisatti D13/700GE Instrucciones De Servicio

Drill
Rated voltage
Current
Frequency
Rated power
No load speed
Max. steel capacity
Chuck clamping range
Weight according EPTA-Procedure 01/2003
Read the operating instructions
Protection category II power tool; double
insulated
In accordance with essential applicable safety
standards of European directives
Wear eye, ear and breath protection
Follow very carefully the instructions in this manual,
save it and keep it close at hand, ready to carry out any
inspection of parts that may be necessary.
If the tool is used with care and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have
bought shall be only those described in this manual.
Any other use of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A "Drilling/Impact Drilling" selector switch (Fig.2) (mod.
DI16/850GE2)
B Keyless chuck (Fig.1, Fig.2 and Fig.3)
C Drill chuck shaft gap (Fig.1, Fig.2 and Fig.3)
D Machine neck (Fig.1 and Fig.2)
E Supply cord (Fig.1 and Fig.2)
F Thumbwheel for speed preselection (Fig.1 and Fig.2)
G Gear selector (Fig.2) (mod. DI16/850GE2)
H Auxiliary grip (Fig.1 and Fig.2)
I Rotational direction switch (Fig.1 and Fig.2)
J On-/off switch (Fig.1 and Fig.2)
K Retainer button (Fig.1 and Fig.2)
EQUIPMENT
- Auxiliary handle
- Depth gauge
- Operating instructions with Safety instructions
- Warranty

BRIEF DESCRIPTION

The machine is intended for drilling in wood, metal,
ceramic and plastic. Machines with electronic control and
right and left rotation are also suitable for screwdriving and
tapping. Any other use not mentioned is not allowed.
Additional drill characteristics
- The rotational direction switch I is used to reverse the

TECHNICAL DATA

D13/700GE
V~
A
Hz
W
rpm
mm
mm
kg
rotational direction of the machine. However, this is not
possible with the On/Off switch J actuated.
- Electronic control of spindle speed, infinitely variable
by finger pressure on the On/off switch J.
The electronic regulation built-in the switch trigger F
-
allows to adjust the speed suitable for the material to be
worked.
- For continuous operation the On-/Off switch can be
locked in the "On" position by the button K.
BEFORE USING THIS TOOL
WARNING! Before carrying out any work, check, for
instance, using a metal detector, that there are no electric
wires or gas or water pipes under the surfaces you wish to
work on.
Make sure the mains voltage is correct: it must be
the same as that on the specification label. Machines with
230V can also be connected to a 220V mains supply.
To turn the machine on, press the ON/OFF switch J
and keep it pressed down.
When the ON/OFF switch is released, the machine
stops.
WARNING! Always disconnect the plug from the
socket before doing any work on the machine.
1. Changing the Tool (fig.3)
WARNING! Before any work on the machine itself,
pull the mains plug.
WARNING! Wear protective gloves when changing
the tool. The drill chuck can become very hot during longer
work periods.
Hold the rear sleeve of the keyless chuck B tight and
turn the front sleeve in opposite rotation direction shown
on fig.3, until the tool can be inserted. Insert the tool. Hold
the rear sleeve of the keyless chuck B tight and firmly
tighten the front sleeve by hand in direction as shown
on fig.3, until the locking action (click) is heard. The drill
chuck is locked automatically. The locking is released
again to remove the tool when the front sleeve is turned
in the opposite direction.
2. Mains connection
WARNING! Connect only to a single-phase AC
current supply and only to the mains voltage specified
on the rating plate. Connection to sockets without earth
protection is possible as the appliance features protective
class II insulation according to European Standard EN
60745. Radio interference suppression complies with the
European Standard EN 60745.
3. Auxiliary handle
WARNING! Operate your machine only with the
auxiliary handle.
D16/850GE
230 230
2.8 3.4
50-60 50-60
710 850
0-1350 0-1000 0-1000 / 0-2500
13 16
1-13 1-13
2.6 2.7
DI16/850GE2
230
3.7
50-60
850
16
1-13
3.0
5