Uline H-2564 Guia De Inicio Rapido
Uline H-2564 Guia De Inicio Rapido

Uline H-2564 Guia De Inicio Rapido

Mesa con armazón en a para pícnic − 8'

Publicidad

Idiomas disponibles

Idiomas disponibles

H-2564
8' A-FRAME
PICNIC TABLE
TOOLS NEEDED
7/16" (11 mm) Socket Bit
Power Drill
Seat Board x 2
Tabletop Board x 3
NOTE: It is important to keep the lag screws loose
throughout assembly. Tighten during step 6.
WARNING! Do not lean on tabletop or seats
when assembling.
1. Verify all parts are present before beginning.
2. Place the three A-Frame bases on a flat, level surface.
3. Place one seat board on each side of the A-Frame
bases. Align the pre-drilled holes over the middle of
the A-Frame base supports. Seat board should be
flush with the end of support.
Figure 1
PAGE 1 OF 6
1-800-295-5510
uline.com
Two Person Assembly
(Optional)
PARTS
Leg Brace Board x 1
ASSEMBLY
Pour le français, consulter les pages 5-6.
A-Frame Base x 3
4. Loosely attach seat boards to A-Frame base with the
3⁄" lag screws and washers using the power drill and
7/16" socket bit (will tighten later in step 6). (See Figure 1)
5. Place the three tabletop boards on the A-Frame bases.
Align the pre-drilled holes with the A-Frame base.
Loosely attach tabletop board slats to A-Frame base
with the 3⁄" lag screws and washers using the power
drill and 7/16" socket bit (will tighten later in step 6).
(See Figure 2)
6. Make sure the table is square and tighten all lag
screws.
Figure 2
Para Español, vea páginas 3-4.
Washer x 33
3⁄" Lag Screw x 33
0721 IH-2564

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Uline H-2564

  • Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-2564 1-800-295-5510 uline.com 8' A-FRAME PICNIC TABLE TOOLS NEEDED 7/16" (11 mm) Socket Bit Two Person Assembly Power Drill (Optional) PARTS Washer x 33 Seat Board x 2...
  • Página 2 7. Attach leg brace board to the underside of the A-Frame bases with the 3½" lag screws and washers using the power drill. (See Figure 3) NOTE: H-6681 Mounting hardware sold separately. Figure 3 1-800-295-5510 PAGE 2 OF 6 0721 IH-2564 uline.com...
  • Página 3: Herramientas Necesarias

    H-2564 800-295-5510 uline.mx MESA CON ARMAZÓN EN A PARA PÍCNIC − 8' HERRAMIENTAS NECESARIAS Dado de 11 mm (7/16") Dos Personas para el Taladro Eléctrico Ensamble (Opcional) PARTES 33 Rondanas 3 Tablas para 2 Tablas para 1 Tabla de Soporte...
  • Página 4: Continuación De Ensamble

    Armazón en A con los tornillos tirafondo de 3½" y las rondanas utilizando el taladro eléctrico. (Vea Diagrama 3) NOTA: La Tornillería de Instalación H-6681 se vende por separado. Diagrama 3 800-295-5510 PAGE 4 OF 6 0721 IH-2564 uline.mx...
  • Página 5: Outils Requis

    H-2564 1-800-295-5510 uline.ca TABLE À PIQUE-NIQUE EN A – 8 pi OUTILS REQUIS Douille tournevis de 11 mm (7/16 po) Montage à deux Perceuse électrique personnes (optionnel) PIÈCES Planche de Planche du dessus Renfort de Tire-fond de Rondelle x 33 Base en forme siège x 2...
  • Página 6 7. À l'aide de la perceuse, fixez le renfort de pied sur la face inférieure des bases en A avec les tire-fonds de 3½ po et les rondelles. (Voir Figure 3) REMARQUE : Le matériel d'installation H-6681 est vendu séparément. Figure 3 1-800-295-5510 PAGE 6 OF 6 0721 IH-2564 uline.ca...

Tabla de contenido