Galletti AREO AC-P Manual Del Usuario página 5

AREO ACP
DECLARATION OF CONFORMITY
Galletti S.p.A. whose main office is located at 12/a via Romagnoli,
40010 Bentivoglio (BO) - - Italy, hereby declares, under its own
responsibility, that the fan heaters belonging to the AREO
AC P series, indoor units for air-conditioning systems, conform to
the specifications of 2006/42/CE, 2004/108/CE, 2006/95/CE and
subsequent modifications.
Bologna, 16/12/2014
SAFETY SYMBOLS
ATTENTION
Carefully read
this manual
GENERAL WARRANTY FOR GALLETTI FAN HEATERS
1) Galletti SpA fan heaters are guaranteed for 24 months from
the date of delivery to the user. The warranty covers free of
charge repairs and/or replacements of components with
"defects" or manufacturing defects.
2) Galletti ties granting the guarantee to the verification of component
defects, through a Service Center authorised by the writer for the
competent territory.
3) In accordance with Directive 199/44/EC implemented by Legislative
Decree no 24 (February 2nd, 2002), the Galletti warranty only applies
to the product and does not contemplate any part of the system.
4) The effective date of the guarantee will be in accordance with the
accompanying bill of sale. In its absence, Galletti reserves the right
to establish the effective date at the date of manufacture.
5) After expiry of the warranty term, spare parts and labour repair costs
are charged to the customer.
6) As specified by law (LD 199), the guarantee obligation for the end user
shall be borne by the seller (the company where the purchase was
made). Galletti will activate warranty procedures upon request by the
seller.
7) The Galletti warranty does not cover:
- Inspection, maintenance, repairs due to normal wear and tear
- Incorrect or non-conforming installation
- Damage caused by transport and / or handling not claimed upon
delivery
- Misuse
- Power supply not "compliant" with the nameplate data
- Damage or manipulation by unauthorised personnel
- Acts of vandalism and weather damage.
8) Galletti reserves the right to challenge the validity of the guarantee
should objective evidence show that the product worked prior to the
effective date of the guarantee.
9) The modalities of these warranty conditions are valid and applicable
only for the Italian territory.
È severamente vietata la riproduzione anche parziale di questo manuale / All copying, even partial, of this manual is strictly forbidden
Luca Galletti
President
DANGER
VOLTAGE
1 BEFORE STARTING INSTALLATION
Carefully read this handbook.
Installation and maintenance must be performed exclusively by technical
personnel qualified for this type of equipment, in compliance with applicable
regulations.
On receiving the equipment check its status, verifying that it has not been
damaged during shipping.
2 INTENDED USE AND OPERATING LIMITS
Galletti S.p.A. will not accept any liability for damage or injury caused as
a result of:
- installation by non-qualified personnel;
- improper use or use in conditions not allowed by the manufacturer;
- failure to perform the maintenance prescribed in this manual;
- use of spare parts other than original factory parts.
The operating limits are specified at the end of this chapter; usage
outside the stated limits is to be considered improper.
When choosing an installation site, you should observe the following
rules:
- The heating unit should not be placed immediately under a socket.
- do not install the unit in places where inflammable gases are present;
- do not expose the unit directly to sprays of water;
- install the unit on walls or ceilings able to withstand its weight; use
accessories suited to the purpose and suitable screw anchors.
Store the unit in its packing container until you are ready to install it in
order to prevent dust infiltrations.
Carry out installation, maintenance and cleaning
operations with the power supply disconnected.
If the unit is installed in a room that is only occasionally used, the
temperature in the room itself must be kept above 0°C or else antifreeze
must be added to the water in order to prevent it from freezing inside the
coil.
Do not attempt to modify the internal wiring or other parts of the unit.
Operating limits
- Thermal carrier fluid: water
- Water temperature: max +95°C
- Air temperature: min -10°C, max + 40°C
- Supply voltage: rated voltage +/- 10%
- Max water pressure during operation: 10 bar
The range comprises 36 models whose characteristics are summarised
in the table of figure 1 where:
RPM number of motor revolutions
Q A air flow rate
PT thermal heating power (70/60°C, 20°C)
Hmax maximum installation height
LWA sound power level
PIN Power consumption
3 UNIT DESCRIPTION
AREO ACP, an indoor terminal unit for heating medium to large interiors
with a horizontal discharge of warm air, consists of the following main
components:
- A pre-painted sheet steel cabinet, complete with ABS corner
trim.
The cabinet is complete with adjustable aluminium louvers (spring
operated) placed on the air outlet which enable an optimal distribution
of air within the room.
On the rear of the cabinet there are 4 for suspending the fan
heater from the ceiling or joining it to the mounting board for installation
on the wall (accessory DFC, DFP or DFO).
- Heat exchanger, made up of copper tubing and aluminium fins
providing superior thermal conductivity compared with traditional iron
pipe exchangers.
- Electric motors:
two-speed, 4/6-pole or 6/8-pole, in 400V three-phase delta-triangle
configuration
5
GB
AP66000756 - 02