Assembly And Adjustments - DeWalt DWE46106 Traducido De Las Instrucciones Originales

EngLIsh
Soft Start Feature
The soft start feature allows a slow speed build-up to avoid an
initial jerk when starting. This feature is particularly useful when
working in confined spaces.
No-Volt
The No-volt function stops the cut-off tool restarting without
the switch being cycled if there is a break in the power supply.
Electronic Clutch
The electronic torque limiting clutch reduces the maximum
torque reaction transmitted to the operator in case of jamming
of a disc. This feature also prevents the gearing and electric
motor from stalling. The torque limiting clutch has been factory-
set and cannot be adjusted.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Attaching Side Handle (Fig. B)

WARNING: Before using the tool, check that the handle is
tightened securely.
Screw the side handle 4 tightly into one of the holes on either
side of the gear case. The side handle should always be used to
maintain control of the tool at all times.
Mounting and Removing the Cutting Shroud
Mounting the DWE46225 125 mm Cutting Shroud
(Fig. A, C, D)

WARNING: It is not possible to use the cut-off tool with a
with a protective guard for grinding applications.
1. Press the front shroud button
shroud button 14 at the same time to fully open the
cutting shroud (Fig. D).
2. Loosen the collar screw 8
the tabs on the cutting shroud with the slots
20
cut-off tool gear case.
3. Rotate the shroud into the desired working position. The
shroud should be positioned between the spindle and the
operator to provide optimum efficiency.
4. Tighten the collar screw 8
the gear case. Do not operate the cut-off tool with a loose
cutting shroud.
5. To remove the cutting shroud, loosen the collar screw,
rotate the cutting shroud to align the slots and tabs and pull
up on the cutting shroud.
nOtE: The cutting shroud is pre-adjusted to the diameter of the
gear case hub at the factory. If, after a period of time, the cutting
shroud becomes loose, tighten the collar screw
NOTICE: If cutting shroud cannot be secured by
tightening the collar screw, do not use tool. Take the tool
26
and the side
13
on the cutting shroud and align
on the
21
to secure the cutting shroud on
8 .
and cutting shroud to a service centre to repair or replace
the cutting shroud.
Mounting and Using Diamond Cutting
Wheels (Fig. A, D, E)

WARNING: Only diamond wheels with a negative
rake angle shall be used with cutting shroud. Do not
cut metal. Do not use with bonded abrasive wheels.
1. With the cutting shroud attached to the cut-off tool, press
the front shroud button 13
at the same time to fully open the cutting shroud.
2. Install the backing flange,
17
3. Place the wheel on the locking flange
24
both on the spindle, against the backing flange, centering
the wheel on the raised center of the backing flange.
4. While depressing the spindle lock button, tighten the
locking flange:
- Tighten standard locking flange using a wrench.
5. After the diamond cutting wheel is mounted, the cutting
shroud must be closed by pressing the front shroud
button and the side shroud button
13
same time.
6. To remove the wheel, depress the spindle lock button and
loosen the locking flange.
Depth of Cut Adjustment (Fig. A)
1. Loosen the depth of cut adjustment knob
2. Slide the depth of cut adjustor
note: If the shroud is closed, press the front shroud
button 13 to open the shroud. This will make it easier to
move the depth of cut adjustor.
3. Tighten the depth of cut adjustment knob.
Dust Extraction (Fig. A, F)

WARNING: Use only power tools recommended by
D WALT with this attachment.
e
For more information about D
with this attachment, please contact one of the authorized
services centers listed on the back cover or refer to the full
details of our after-sales service available on the Internet at:
www.2helpU.com.

WARNING: This attachment must be used with a dust
extractor system. ALWAYS wear certified safety face or
dust mask.
nOtE: Ensure hose connection is secure.
nOtE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor vacuum instruction manual for more information.
All D WALT dust collection shrouds are designed to work with
e
the D WALT Airlock DWV9000 connector.
e
1. Attach the DWV9000 connector
hose 23 .
2. Unlock the DWV9000 connector
port .
7
3. Lock the DWV9000 connector
and the side shroud button
, on spindle .
3
, and place
18
at the
14
11 .
to the desired position.
10
WALT power tools compatible
e
to your dust collector
22
22 and slide onto dust
22 to secure.
14