Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Note: Relocation or removal of the
under-vehicle spare tire is not required.
Equipment Required:
Fastener Kit: 01130-707
Fastener Kit: 01130-707
Wrenches: 18mm, 19mm, 13/16, 7/8
Wrenches: 18mm, 19mm, 13/16, 7/8
Drill Bits: 9/16
Drill Bits: 9/16
Hitch Requires 5/8" pin and clip
Hitch Requires 5/8" pin and clip
j
Qty. (4)
9/16 X 1.75 GR5 Hex Bolt
k
Qty. (4)
3/8 X 1-1/2 X 3 Block
l
Qty. (4)
Flanged Locknut
m
Qty. (2)
M12 X 1.75 X 45mm CL10.9 Bolt
n
Qty. (2)
Conical Toothed Washer
Warning: Under No Circumstances is this hitch to be installed on vehicles with a 6' box (short wheelbase).
1.
If vehicle is equipped with a factory step bumper, remove and discard the 12mm hex bolt from each end of the frame.
2.
Vehicles W/O Factory Step Bumper: Using the existing holes in the frame rails, bolt the reinforcement bracket into the inside
end of each frame rail using 1/2" X 1.25" hex bolts, 1/2" hex nuts and lockwashers. The reinforcement brackets should rest
against the frame rail lower flanges.
3.
Lift receiver into position, centering over the existing holes in the frame.
Vehicles W/O Factory Step Bumper: Install The M12 X 1.75 X 45mm hex bolt and 1/2" conical toothed washer through the
4.
receiver bracket, frame rail and reinforcement bracket. Install the 1/2" lockwasher and M12 X 1.75 hex nut.
Vehicles W/ Factory Step Bumper: Install the M12 X 1.75 X 45mm hex bolt and 1/2" conical toothed washer through the
4.
receiver bracket, into the frame, threading into the existing weld nut. The M12 hex nuts, 1/2" X 1.25" hex bolts, 1/2" hex nuts,
1/2" lockwashers and the reinforcement brackets may be discarded.
Increase the center attachment hole to 9/16".
5.
6.
Install the remaining fasteners as shown, placing the blocks inside the frame rails.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008, 2012 Cequent Performance Products
Installation Instructions
Chevrolet & GMC Pickup
Full Size – All With 8' Box
For vehicles without
step bumper
Existing weldnut (With
step bumper only)
Tighten all M12 CL8.8 fasteners with torque wrench to 85 Lb.-Ft. (116 N*M)
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all 9/16 GR5 fasteners with torque wrench to 120 Lb.-Ft. (163 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU4
Frame
o
Qty. (4)
1/2 X 1-1/4 GR5 Hex Bolt
p
Qty. (6)
Lock Washer
q
Qty. (4)
1/2-13 Hex Nut
r
Qty. (2)
M12 X 1.75 Nut
Sheet 1 of 3
N41901
Part Numbers:
41901
96901
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
13,000 (5902 Kg)
1300 (590 Kg)
10,000 (4540 Kg)
1000 (454 Kg)
R.H./L.H. Bracket
(4357-001, 4357-002)
6-1-12
Rev. C

Publicidad

loading

Resumen de contenidos para Cequent Performance Products 41901

  • Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2008, 2012 Cequent Performance Products Sheet 1 of 3 N41901 6-1-12 Rev.
  • Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2008, 2012 Cequent Performance Products Feuille 2 de 3 N41901 6-1-12 Rev.
  • Página 3 No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2008, 2012 Cequent Performance Products Sheet 3 of 3...

Este manual también es adecuado para:

96901