TESY LD-168D Instrucciones De Uso página 2

This appliance has been manufactured for TESY Ltd,
EN
Shumen, 48 Madara Boulevard (P.O. Box 529) by
Jiasheng (Zhongshan) Electrical Appliances Co., Ltd.
This is an I3B/P(30) category appliance with maximum
power output of 4.2 kW and fuel consumption of
305 g/hour. This appliance works with propane butane
gas (G30/31) with a pressure of 30 mbar. The amount of
air required for the correct burning process is 8,4 m3/h.
ASSEMBLING THE WHEELS:
Take out the wheels from the packaging. Turn the heater
unit upside down and place it if possible on a carpet or
over another soft surface so as not to damage its finish.
Press the wheels over their respective rivets until a click
is heard.
CAUTION! BASIC SAFETY INSTRUCTIONS FOR USE:
•
Use the heater only in accordance with these
instructions;
•
Use only in well ventilated areas;
•
This appliance should not be used in premises
such as basements, bathrooms, or bedrooms and
in rooms with a volume less than 15 m3 (30 m3 for
living rooms);
•
The gases resulting from the burning process are
expelled in the atmosphere of the premise being
heated;
•
The heater's protective grill protects from the
spread of fire or burns and must not be removed.
The grill does not offer full protection for children
and persons with ailments;
•
Do not place clothes or other materials over the
heater. If you do not adhere to this warning you
could risk causing a fire, or reduce the appliance's
effective functioning;
•
Do not move the appliance when in operation;
•
Minimum distance from side walls to heater – 20 cm;
•
Do not place heater in the immediate vicinity of
curtains, armchairs or other flammable materials;
•
Always position the heater facing the room's center
during use and allow for a distance of at least 1.5
meters between the appliance's front and other
objects and at least 0.2 m to the appliance's sides
and back. In case the heater has been placed on
a surface which may be turned over (by children,
household pets, etc), you must take special
measures;
•
Make sure the assembly complies to the local
standards;
•
When changing gas canisters make sure there's no
open flame in the nearby vicinity;
•
The gas canister must be in an upright position
during use.
2
Usage and Storage Instructions
Don't move the heater while in operation. The tip-over
switch may be activated and turn the heater off.
Do not under any circumstances flip the canister upside
down in order to use the remaining gas content.
GAS LEAKS:
In case you suspect a gas leak, stop the gas flow from
the gas canister and let fresh air in the room.
Do not remove the pressure regulator. Do not place
near an open flame.Turn on the gas feed slowly and
moisten all connections with a water and soap solution
or with liquid detergent - if a gas leak is present, bubbles
shall appear. If a gas leak is established call a gas heater
service center.
Do not use the heater unless it has been repaired!
Never use matches to locate a suspected gas leak!
CHANGING OF GAS BOTTLE:
Canging of gas bottle must not be carried out in the
presence of a naked flame. Use the gas bottle always
in upright position. Ifa screw on regulator is used
ensure that the regulator washer is present and in good
condition - replace if in any doubt. toplace the bottle in
position, remove the rear panel which faces the inside
during transport, by unfastening the screws; than put
the bottle in position and replase the panel. Do not turn
the bottle upside down to use completely its content.
GAS BOTTLE:
The fueling of the gas heater is carried out via a canister
with a work pressure of 30 mbar provided by a dual
stage pressure reducing valve.
The maximum capacity of the gas bottle is 15 kg (height
from 440mm to 600mm, diameter up to 330mm).
In order to install the bottle remove the back cover,
which is placed facing the interior during transportation,
and place the bottle at its predestinated spot and put
the cover back in its position.
PRESSURE REGULATOR, FLEXIBLE PIPE AND
RETAINING RINGS:
This appliance works with a 30 mbar pressure regulator
and a flexible pipe.
Check if the flexible pipe has entirely covered the stub
pipes and make sure that the retaining rings have
been placed securely at both ends. When connecting
the pressure regulator and the gas canister avoid the
flexible pipe's excessive twisting.
This appliance must be connected to a pressure
regulator for propane butane fuel with pressure of 30
mbar in compliance with the local national standards.