General Power Tool Safety Warnings; Work Area Safety; Electrical Safety; Personal Safety - DeWalt D26420 Traducido De Las Instrucciones Originales

2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-4:2009
+A11:2011.
These products also comply with Directive, 2014/30/EU and
2011/65/EU. For more information, please contact D
the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of D
Markus Rompel
Director Engineering
D WALT, Richard-Klinger-Straße 11,
e
D-65510, Idstein, Germany
20.04.2016
WARNING: To reduce the risk of injury, read the
instruction manual.

General Power Tool Safety Warnings


WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.

1) Work area safety

a ) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b ) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c ) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.

2) Electrical safety

a ) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b ) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c ) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d ) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
e ) When operating a power tool outdoors, use an
WALT at
e
f ) If operating a power tool in a damp location is
WALT.
e

3) Personal safety

a ) Stay alert, watch what you are doing and use
b ) Use personal protective equipment. Always wear
c ) Prevent unintentional starting. Ensure the switch
d ) Remove any adjusting key or wrench before turning
e ) Do not overreach. Keep proper footing and balance
f ) Dress properly. Do not wear loose clothing or
g ) If devices are provided for the connection of dust
4) Power tool use and care
a ) Do not force the power tool. Use the correct power
b ) Do not use the power tool if the switch does not turn
c ) Disconnect the plug from the power source and/or
parts. Damaged or entangled cords increase the risk of
electric shock.
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
eye protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
is in the off position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personal injury.
at all times. This enables better control of the power tool
in unexpected situations.
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
tool for your application. The correct power tool
will do the job better and safer at the rate for which it
was designed.
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
EngLIsh
17