Dip7 Function; Functions On Sliding Elements; Learning Of Transmitters; Service Man Present Function - Key Automation CT1RS Instrucciones Y Advertencias Para Su Instalación Y Uso

5.10 - DIP7 Function

PERSON PRESENT
The OPEN command and the CLOSE command open as long as they are held down.
The SBS command is ignored, even by the transmitter.
6 - FUNCTIONS FOR ROLLING SHUTTERS

6.1 - Learning of transmitters

After a total cancellation of the transmitters, the first taught
transmitter sets the Rolling Code or Fixed Code mode for all the
other transmitters.
STEP-BY-STEP FUNCTION LEARNING:
Press and hold P2 until the DL6 LED slowly flashes
orange, release. Activate the transmitter to undergo
learning until the DL6 LED turns green.
(Led DL6 orange reception error, Led DL6 red memory
full - 250 buttons). The SBS function does not work if
DIP8=OFF and DIP7=ON.
PARTIAL FUNCTION LEARNING: Press and hold P2
until LED DL6 slowly flashes orange, do not release,
wait for rapid flashing. Activate the transmitter to undergo
learning until the DL6 LED turns green. (LED DL6 orange
reception error, LED DL6 red memory full)
SINGLE BUTTON CANCELLATION:
Press and hold P2 until the DL6 LED slowly flashes
orange, do not release, wait for rapid flashing, do not
release, wait for very rapid flashing. Activate the button to
be deleted until the DL6 LED turns green (if the reception
error is orange)
TRANSMITTER TOTAL CANCELLATION:
Turn on the appliance by holding down P2 until the DL6
LED quickly flashes orange, do not release, wait for
green flashing. All transmitters canceled.
6.2 - Man present function
Press P1 and P2 simultaneously until the DL6 LED turns
red. P1 opens man present, P2 closes man present.
Press P1 and P2 simultaneously to exit the mode.
6.3 - Learning of the STROKE and of the PARTIAL OPENING function
The operation must be performed with the gate
CLOSED. Keep P1 pressed until the DL6 LED flashes
red. Release P1. Pressing and releasing P2 starts fast
opening, pressing and releasing P2 starts slowing down,
the motor stops on the limit switch during opening. After 2
sec it starts fast closing, pressing and releasing P2 starts
slowing down, the motor stops on the closing limit switch.
After 2 sec it starts PARTIAL OPENING, pressing and
releasing P2 stops partial opening. After 2 sec it starts
closing up to the closing limit switch. The motor speed
is determined by Trimmer 2, also in learning, so first set
TR2 and then perform the learning.
The SBS function will behave according to the settings of DIP2 and
DIP3. The PARTIAL function is only available with the transmitter.
2 s
3s
FLASHING -
SLOW
ORANGE
P2
2 s
3s
FLASHING -
SLOW
ORANGE
P2
2 s 1 s
3s
FLASHING - FLASHING -
SLOW FAST
ORANGE ORANGE
P2
2 s
3s
FLASHING -
SLOW
ORANGE
P2
3s 3s
ON
RED
P1 + P2 P1
2 s
3s
FLASHING -
SLOW
RED
P1 P2
OFF
NOT ENABLED ENABLED
3s
1 s
3s
FLASHING -
FAST
ORANGE
0.5 s
3s
FLASHINGVERY
FAST
ORANGE
1 s
FLASHING - FLASHING -
FAST SLOW
ORANGE GREEN
3s
P2
2 Sec. 2 Sec.
P2 P2 P2
EN
ON
ON
GREEN
ON
GREEN
ON
GREEN
2 s
3s
P1 + P2
2 Sec.
23