Operation And Maintenance; Technical Parameters - GRAPHITE 58G031 Manual Del Usuario

off after some time. Disconnect power supply before removing
the battery from the charger socket. Avoid consecutive short
chargings. Do not charge the battery after short use of the tool.
Significant decrease of the period between chargings indicates
the battery is worn out and should be replaced.
Batteries heat up when charging. Do not operate just after
charging – wait for the battery to cool down to room temperature.
It will prevent battery damage.
BATTERY LEVEL INDICATION
The battery is equipped with battery level indicator (3 LED diodes)
(9). To check battery level status, press the button for battery level
indication (8) (fig. C). When all diodes are lit, the battery level is high.
When 2 diodes are on, the battery is partially discharged. When only
one diode is lit, the battery is discharged and must be recharged.
INSTALLATION / DEINSTALLATION OF NOZZLE
• To install the nozzle (1) on the blower, slide it onto the stub until
the nozzle lock button (2) snaps on (fig. C) (fig. D).
• To disassemble, press in the nozzle lock button (2) and slide off the
nozzle (1) from the stub (fig. E).
OPERATION / SETTINGS
SWITCHING ON / OFF
Switching on
• Slide the switch (3) forward to position I.
Switching off
• Slide the switch (3) back to position O (fig. F).

OPERATION AND MAINTENANCE

Remove the battery from the device before commencing
any activities related to installation, adjustment, repair or
maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device immediately after each use is recommended.
• If possible, motor casing should be always free from dust and dirt.
• Wipe the device with a clean cloth or blow through with
compressed air at low pressure.
• Do not clean with water or chemical cleaning agents.
• Be careful to avoid ingress of water into the device.
• Use only original equipment and original spare parts.
• When not in use, store the tool in a dry place, beyond reach of
children.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized by
the manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS
Cordless Leaf Blower 58G031
Parameter
Battery voltage
Motor speed
Air flow speed
Protection class
Weight
Year of production
58G031 defines type and indication of the device
Battery
Battery voltage
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Charger type
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Ambient temperature range
Charging time of the battery 58G001
Charging time of the battery 58G004
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure
Sound power
Vibration acceleration
Noise and vibration information
Noise produced by the device is defined with: level of produced
sound pressure L
measurement uncertainty). Vibrations produced by the device
are defined with vibration acceleration value a
measurement uncertainty).
Sound pressure L
specified in this manual have been measured in accordance with the
standard EN 60335-1:2012; EN 50636. Specified vibration level a
be used to compare tools and for initial evaluation of exposition to
vibrations.
Specified vibration level is typical only for the main applications
of the device. When the device is used for other purposes or with
different working tools, the vibration level may change. Insufficient
or too rare maintenance may increase vibration level. The
Value
abovementioned factors may lead to higher exposure to vibrations
18 V DC
during whole working time.
To precisely define exposure to vibrations, include periods
12000 min
-1
when the device is switched off and when it is switched on
but not used for working. Once all factors have been carefully
190 km/h
considered, total exposition to vibrations may be significantly
III
lower.
To protect the user from results of exposure to vibrations, use
1,2 kg
additional safety measures such as: device and working tool periodic
2019
maintenance, proper hand temperature conditions, good work
organisation.
13
Graphite Energy+ System Battery
Parameter
58G001
18 V DC
Li-Ion
2000 mAh
4 C – 40
0
1 h
0,400 kg
2019
Graphite Energy+ System Charger
Parameter
L = 81,2 dB(A) K= 3 dB(A)
pA
L = 90,4 dB(A) K= 3 dB(A)
wA
a = 2,142 m/s
h
and level of sound power L
pA
, sound power L and vibration acceleration a
pA wA
Value
58G004
18 V DC
Li-Ion
4000 mAh
C 4 C – 40 C
0 0 0
2 h
0,650 kg
2019
Value
58G002
230 V AC
50 Hz
22 V DC
2300 mA
4 0 C – 40 0 C
1 h
2 h
II
0,300 kg
2019
K= 1,5 m/s
2 2
(where K is
wA
(where K is
h
h
can
h