Tools Required For Assembly - Agri-Fab 45-02941 Manual Del Usuario

For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
ASSEMBlY INSTRUCTIONS

TOOlS REQUIRED FOR ASSEMBlY

(2) 1/2" wrenches
(1) 9/16" wrench
(1) 3/4" wrench or adjustable wrench
(1) Pliers
(1) Phillips screw driver or a round punch
Before assembling the de-thatcher, lay out all of the parts
and hardware as shown on the previous pages.
The 40" dethatcher is shown in the drawings. T he assembly
procedure is the same for the 48" dethatcher.
1. Assemble the lift plate to the top of the tine shield
using four 5/16" x 1" hex bolts and 5/16" nylock nuts
as shown in figure 1. Tighten.
LIFT PLATE
FIGURE 1
2. Turn the tine shield upside down. See figure 2.
3. Assemble two (tall) hitch arm mount brackets and
two (short) angle brackets to the bottom of the tine
shield at the rear. Use four 5/16" x 1" hex bolts and
5/16" nylock nuts. Do not tighten yet. Position the
brackets as shown in figure 2.
4. Assemble two angle brackets to the bottom of the
tine shield at the front. Use two 5/16" x 1" hex bolts
and 5/16" nylock nuts. Do not tighten yet. Position
the brackets as shown in figure 2.
HITCH ARM MOUNT BRACKETS
ANGLE BRACKET
5/16" NYLOCK NUT
REAR
5/16" x 1"
HEX BOLT
FIGURE 2
ENGlISH
5/16" x 1"
HEX BOLT
5/16" NYLOCK NUT
ANGLE BRACKET
ANGLE
BRACKETS
www.mymowerparts.com
5. Fasten the hitch mount arms to the outside of the
angle brackets at the front of the tine shield. Use two
5/16" x 1" hex bolts and 5/16" nylock nuts. Tighten
and then loosen the nuts slightly. See figure 3.
6. Fasten the hitch mount arms to the outside of the hitch
arm mount brackets at the rear of the tine shield. Use
two 5/16" x 1" carriage bolts, and 5/16" nylock nuts.
Do not tighten yet. See figure 3.
5/16"
NYLOCK
NUT
5/16" NYLOCK NUT
FIGURE 3
7. Assemble the front ends of the hitch mount arms
together using two 5/16" x 1-1/4" hex bolts and 5/16"
nylock nuts. Do not tighten yet. See figure 4.
8. Assemble the hitch brackets to the top and bottom of
the hitch mount arms using two 5/16" x 2" hex bolts
and 5/16" nylock nuts. Do not tighten yet. See figure
4.
9. Assemble the 3/8" hitch pin through the hitch brackets
and secure it with a 1/8" hair cotter pin. See figure
4.
5/16" x 1-1/4"
HEX BOLT
5/16" x 2"
HEX BOLT
FIGURE 4
10. Tighten the bolts and nuts assembled in step 8.
Tighten the bolts and nuts assembled in step 7.
Tighten the bolts and nuts assembled in step 3.
Tighten the bolts and nuts assembled in step 4.
Tighten and then loosen slightly the bolts and nuts
assembled in step 5.
Tighten the bolts and nuts assembled in step 6.
4
5/16" x 1"
CARRIAGE BOLT
5/16" x 1"
HEX BOLT
HITCH MOUNT ARMS
5/16" NYLOCK NUT
1/8" HAIR
COTTER PIN
HITCH
BRACKET
3/8" HITCH PIN