BaByliss PARIS CURL SECRET 2 C1300E Manual De Instrucciones página 5

• Select the accessory according to the type of curls desired:
- 25 mm: tight curls
- 35 mm: volume and larger curls
• Always position or remove accessories before plugging the appliance
in and switching it on.
• To remove the accessory, press the two buttons on the two sides of the
accessory at the same time, using your thumb and index finger (FIG. 1).
• To position the accessory, place it onto the appliance head until it clicks
in.
• Plug in the appliance, switch on, and select the desired temperature
using the 0-I-II switch. See table below:
Temperature Temperature
Ø 35 mm Ø 25 mm
(I): (I):
190°C 210°C
(II): (II):
210°C 230°C
• The indicator light comes on and will start to flash.
• The indicator light will stop flashing when the appliance has heated
up to the selected temperature. The appliance is now ready to use; the
indicator light will stay on.
• Select the time setting depending on the desired curl effect. For loose
curls, select the minimum time setting. For tighter curls, select the
maximum time setting. Please refer to the table below:
Time Audio beep indicator
8 seconds (Ø 35 mm) 3 beeps (Ø 35 mm)
10 seconds (Ø 25 mm) 4 beeps (Ø 25 mm)
10 seconds (Ø 35 mm) 4 beeps (Ø 35 mm)
12 seconds (Ø 25 mm) 5 beeps (Ø 25 mm)
12 seconds (Ø 35 mm) 5 beeps (Ø 35 mm)
14 seconds (Ø 25 mm) 6 beeps (Ø 25 mm)
• Select the adjustment of the direction of the curl, according to the
desired result:
Hair type
Fine, bleached, and/or
damaged hair
Normal hair, thick and
wavy, or dyed
Curl effect
Loose waves
Soft curls
Defined curls
8
- For an even, more sophisticated style, adjust
the appliance to the "L" (left) position, to
create curls to the left side of the head.
Then adjust the appliance to the "R" (right)
position, to create curls on the right side of
the head.
- For a softer, more natural style, adjust the
appliance to the "A" (automatic) position. This
adjustment will create alternating curls, first
in one direction and then the opposite.
Precautions for use
• Ensure that hair is dry.
• Clip the upper layers to the top of your head and start working on the
layers underneath.
• Separate a section of hair that is no wider than 3 cm. Ensure that there
are no tangles in the section.
• Bring the appliance close to the hair and position it in the correct
direction: the cavity formed by the cylinder downwards (FIG. 2 and 3)
and facing the head (FIG. 4 and 5).
• With your free hand, take hold of the tip of the section of hair and place it
in the opening, in the funnel situated between the two handles (FIG. 6).
Please note: To prevent the appliance from blocking, ensure that you
have no hair lying across the edges.
Also ensure that you are not pulling your hair before activating the
handles (FIG. 7 and 8).
If these precautions are not respected, you risk catching your hair
in the appliance.
• Once the section of hair is in place, close the handles to allow the hair to
automatically enter into the appliance.
• Keep the handles closed until the beeping stops (after 3, 4, 5 or 6 beeps
depending on the selected time setting; see the table above) (FIG. 9).
• Gently release the hair from the appliance by opening the handles
(FIG. 10). Do not pull on the appliance to free the hair. If you do this,
you will ruin the curl effect.
• Allow your hair to cool before handling or combing it.
• Repeat all over the head until you have the number of curls you want.
• After use, switch off and unplug the appliance. Allow to cool before
storing.
9