•
Changing bits e
! push spindle-lock button G only when tool is at a
standstill (6398)
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
•
Adjusting drilling depth r
•
Holding and guiding the tool t
! while working, always hold the tool at the grey-
coloured grip area(s)
- always use auxiliary handle H 2 (can be adjusted
as illustrated)
- keep ventilation slots K 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
•
Use the appropriate bits y
! only use sharp bits
•
For drilling in concrete or stone a steady pressure on the
drill is required
•
When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
•
Splinterfree drilling in wood u
•
Dustfree drilling in walls i
•
Dustfree drilling in ceilings o
•
Drilling in tiles without skidding p
•
For more tips see www.skil.com
MAINTENANCE / SERVICE
•
This tool is not intended for professional use
•
Always keep tool and cord clean (especially ventilation
slots K 2 )
! disconnect the plug before cleaning
•
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONMENT
•
Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
Impact drill 6395 6398
Technical data 1
•
We declare under our sole responsibility that the product
described under "Technical data" is in conformity with
the following standards or standardization documents:
EN 60745, EN 61000, EN 55014, in accordance with
the provisions of the directives 2004/108/EC (until
19.04.2016), 2014/30/EU (from 20.04.2016), 2006/42/
EC, 2011/65/EU
•
Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
Marijn van der Hoofden
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
09.03.2015
16.05.2013
NOISE/VIBRATION
Measured in accordance with EN 60745 the sound
•
pressure level of this tool is 100 dB(A) and the sound
power level 111 dB(A) (standard deviation: 3 dB),
and the vibration . (triax vector sum; uncertainty
K = 1.5 m/s²)
. when drilling in metal 7.1 m/s²
. when impact drilling in concrete 17.0 m/s²
•
The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Perceuse à percussion
INTRODUCTION
•
Cet outil est conçu pour les travaux de perçage de
percussion dans la brique, le béton et dans la pierre
naturelle ainsi que le perçage dans le bois, le métal, la
céramique et les matières plastiques
•
Cet outil n'est conçu pour un usage professionnel
•
Lisez et conservez ce manuel d'instruction 3
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A
Interrupteur de marche/arrêt et réglage de vitesse
B
Bouton de blocage de l'interrupteur
C
Molette de réglage de la vitesse maximum
D
Commutateur pour inverser le sens de rotation
E
Commutateur pour sélectionner la fonction de perçage
F
Indicateur de la fonction de perçage sélectionnée
9
Olaf Dijkgraaf
Approvals Manager
13
6395/6398