Left-hand thread
Before installing, check the blades for damages (notches,
cracks). Damaged blades must be replaced.
All knive edges have become blunt:
Replace with new set of knives (order-no. 382425).
Always replace worn and damaged blades as a whole set to
prevent any unbalance.
M
a
i
n
t
e
n
a
n
c
e
/
C
M
a
i
n
t
e
n
a
n
c
e
/
C
•
Each time before starting maintenance work:
Switch off the motor and pull out the mains plug.
−
Allow the machine to cool down.
−
Wear protective gloves to prevent injury.
−
When the machine is stopped for purpose of maintenance,
storage or accessory replacement make sure that the energy
source is isolated and the mains plug is disconnected. Make
T
e
c
h
n
i
c
a
l
d
a
t
a
T
e
c
h
n
i
c
a
l
d
a
t
a
Type/Model
Year of construction
Motor
Motor rating P
S6 - 40 %
1
Motor rating P
S1
1
Current consumption I
ON/OFF-switch with
Weight
Sound pressure level at work L
Measured sound power level L
Guaranteed sound power level L
Max. branch diameter (only for freshly cut wood)
Safety class
Protection class
Mains fuse
Suisse
UK
Operating mode:
S1
Continuous operation
l
e
a
n
i
n
g
/
S
t
o
r
a
g
e
l
e
a
n
i
n
g
/
S
t
o
r
a
g
e
PA
WA
WA
sure that all movable parts are stationary and the key (if
applicable) is removed. Allow the machine to cool down
before maintenance, adjustment etc.
The cutters will not come to a standstill immediately after
cut-off. Before starting any service work wait until all parts
are stationary.
When performing maintenance operations on the cutting tool
be aware that it can still move due to the start mechanism
even if the motor does not run by the cover interlocking.
Be sure to have removed any tools from the machine after
completion of service work.
Generally garden shredders require little maintenance. To
•
maintain their efficiency and a long life, observe the fol-
lowing:
Keep vent slits clean and free from obstructions.
−
Check the locking screws (tighten where necessary).
−
Clean the device after shredding.
−
To clean your product only use a warm moist cloth and a soft
brush.
Never use cleaning agents or solvents. Otherwise the device
may be damaged irreversibly. Plastic parts may be corroded
by chemicals.
Do not clean the machine with running water or high-pressure
−
cleaners.
After each operation treat bare metal parts with an environ-
−
ment-compatible biodegradable spray oil to protect them
against corrosion.
AMA 2300
AC-Motor 230 V~, 50 Hz, 2800 rpm, including automatic motor brake
2300 W
2000 W
10,4 A
Motor protection switch, electrical safety cut-out, zero-voltage initiator
83 dB (A) / K = 3 dB (A) (measured to 2000/14/EC)
107 dB (A) (measured to 2000/14/EC)
108 dB (A) (measured to 2000/14/EC)
16 A time-lag
10 A time-lag
13 A time-lag
S 6 – 40 %
Continuous intermittent operation
For 10 min.:
4 min. continuous operation
6 min. operation at no or low load
AMA 2500
see last page
2500 W
2000 W
11,3 A
18,5 kg
∅ max. 40 mm
I
IP X4
16 A time-lag
13 A time-lag
15