Noise Information; English - AEG POWERTOOLS TS 250 K Manual Original

TECHNICAL DATA
Circular table saw
Production code
Rated input
Rated current
No-load speed
Saw blade dia. x hole dia
Saw blade thickness
Max. Cutting depth at 90°
Max. Cutting depth at 45°
Weight according EPTA-Procedure 01/2003

Noise information

Measured values determined according to EN 61029. Typically, the
A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
WARNING! When using electric tools basic safety precautions
GB
should always be followed to reduce the risk of fire, electric shock and
personal injury including the following. Read all these instruc-
tions before attempting to operate this product and save these
instructions.
CIRCULAR SAW SAFETY WARNINGS
Wear ear protectors. Exposure to noise can cause hearing loss.
Use protective equipment. Always wear safety glasses when working
with the machine. The use of protective clothing is recommended,
such as dust mask, protective gloves, sturdy non-slip footwear,
helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do
not inhale the dust. Use a dust absorption system and wear a suitable
dust protection mask. Remove deposited dust thoroughly, e.g. with
a vacuum cleaner.
Ensure that the machine is always stable and secure.
Before using the tool please read the instructions. If possible have the
tool demonstrated.
Adjust the riving knife as described in this instruction manual.
Incorrect spacing, positioning and alignment can make the riving
knife ineffective in preventing kickback.
Do not use saw blades which are damaged or deformed
Only use saw blades which have been properly sharpened.
Do not use saw blades not corresponding to the key data given in
these instructions for use.
The teeth thickness, or the set of the teeth must be thicker than the
body of the blade and the riving knife. Do not remove the riving knife.
To minimise noise, the tool must be sharpened and all noise reducing
elements (covers etc.) must be properly adjusted.
Only use tools that meet standard EN 847-1.
Transport and store the tools in a suitable receptacle;
It is necessary to select a saw blade which is suitable for the material
being cut.
It is essential to adhere to the maximum speed specified on the saw
blade.
Do not use saw blades made of high-speed steel.
Do not use any flanges other than those supplied or indicated in the
instruction manual to secure the saw blade.

English

22
REMOVE ADJUSTING KEYS AND WRENCHES. From habit of checking to
TS 250 K
see that keys and adjusting wrenches are removed from tool before
turning it "ON".
4478 81 02...
Any faults with the machine, including any related to the safeguard
... 000001-999999
or the saw blades, must be reported to the persons in charge of safety
1800 W
as soon as the faults are discovered.
7,5A
Always use the protective shields on the machine.
4800 min
-1
Only use the circular table saw with guards in good working order and
254 x 30 mm
properly maintained, and in position.
1,8 mm
Do not clamp the protective swing guard.
90 mm
Never reach into the danger area of the machine when it is running.
62 mm
For security, use devices such as safety- and pressure device, guide
41 kg
slide, rip fence, etc.
Chips and splinters must not be removed while the machine is
running.
Refrain from removing any cut-offs or other parts of the workpiece
98 dB(A)
from the cutting area whilst the machine is running and the saw head
111 dB(A)
is not in the rest position.
When blade is binding, or when interrupting a cut for any reason,
release the trigger and hold the saw motionless in the material until
the blade comes to a complete stop. Never attempt to remove the
saw from the work or pull the saw backward while the blade is in
motion or kickback may occur. Investigate and take corrective actions
to eliminate the cause of blade binding.
The handle lock must always be engaged when transporting the
circular table saw.
Do not use the top protective cover as a handle for transportation!
Before transporting the machine, make sure that the top protective
guard covers the top section of the saw blade.
Support large panels to minimise the risk of blade pinching and
kickback. Large panels tend to sag under their own weight. Supports
must be placed under the panel on both sides, near the line of cut and
near the edge of the panel.
Keeping rip fence parallel to the saw blade.
MOVE the rip fence out of the way when cross-cutting.
Keep the floor area free of loose material e.g. chips and cut-offs.
In spite of compliance with all relevant design regulations, dangers
may still present themselves when the machine is operated, e.g.:
workpiece parts being thrown off,
parts of damaged tools being thrown off, noise emissions, wood dust
emissions.
Always disconnect the plug from the socket before carrying out any
work on the machine.
SPECIFIED CONDITIONS OF USE
Use this circular saw to cut only wood and wood like products.
Never use the Circular table saw to cut materials other than those
specified in the instruction manual.
Stock having a round or irregular cross section (such as firewood)
must not be cut, as it can not be securely held during cutting. When
sawing thin stock layed on edge, a suitable auxilary fence must be
used for firm support.
Do not use circular saws for cutting slots (grooves in workpiece).
Cutting rebates or grooves is only permitted with a suitable protec-
tive device fi tted, e.g. a protective tunnel over the saw table.