Additional Safety Rules - EINHELL A-S 360 EK Manual Del Usuario

S-Hinweise Stichsaege_Bauhaus:_
GB
danger posed by dust.
4. Using the treatment of electric tools
Do not overload your tool. Only use suitable
electric tools to perform your work.
Using the right electric tool allows you to work
better and safer within the toolʼs quoted capacity
range.
Do not use an electric tool whose switch is
defective.
An electric tool that no longer can be switched on
or off is dangerous and must be repaired.
Pull the plug out of the socket and/or remove
the battery before making any adjustments to
the tool, changing accessories or put the tool
down.
This precaution eliminates the possibility of
inadvertently starting the tool.
When not in use, store electric tools out of the
reach of children. Do not allow those persons
to use this tool who are unfamiliar with it or
who have not read these instructions.
Electric tools are dangerous when they are used
by inexperienced persons.
Take good care of your tool. Check that
moving parts properly function and do not jam,
that parts are not broken off or damaged in any
way and that the tool can be used to its full
capacity. Have damaged parts repaired prior to
using the tool.
The cause of many accidents can be traced back
to poorly maintained electric tools.
Keep your blades sharp and clean.
Properly maintained blades with sharp edges jam
less frequently and are easier to use.
Make sure to use electric tools, accessories,
attachments, etc. in accordance with these
instructions. Take the conditions in your work
area and the job in hand into account.
Using electric tools for applications other than
those intended can lead to dangerous situations.
5. SERVICE
Have your tool repaired only by authorized
specialists using original replacement parts.
This will ensure that your tool remains safe to use.
6
05.08.2008 8:48 Uhr

Additional Safety rules

Always check the saw, the power cable and the
plug before use. Only ever use the saw if it is in
perfect, undamaged condition. Damaged parts
have to be repaired or replaced immediately by a
qualified electrician.
Always pull the plug out of the power socket
before carrying out any work on the saw, before
changing the blade and in periods of non-use.
Always run the power cable away from the back of
the saw to guard it from damage.
For outdoors work use only suitably approved
extension cables with a minimum conductor cross
section of 1,5 mm 2 . The plug connectors must
have earthing contacts and be splash-proof.
Keep the saw in a safe place and out of the reach
of children.
Always wear goggles, safety gloves and ear muffs
when sawing. Wear a breathing mask on dusty
jobs.
Never leave any keys or adjustment spanners in
position on the saw. Before switching on, check
that all keys and adjustment spanners have been
removed.
Secure the workpiece (with a clamp) so that it
cannot slip.
It is imperative to use a dust extractor when wor
king on stone. Make sure the dust extractor is
approved for stone dust.
It is prohibited to use the saw on asbestos
materials.
Please note the accident prevention regulations in
force in your country.
Use only original spare parts.
Repairs are to be carried out by qualified electrici
ans only.
The level of noise at the workplace may exceed
85 dB(A). In this case you will need to introduce
noise protection measures for the user.
Make sure of your footing. Avoid abnormal wor
king positions.
Keep your electric tool out of the rain. Never use
electric tools in wet or damp conditions, and never
use them near inflammable liquids.
Never carry the electric tool by its power cable.
Keep the power cable safe from damage. Oil, sol
vent and sharp edges can damage cables.
Keep your workplace tidy.
Make sure the power switch is off before inserting
the plug in the socket.
Wear suitable clothing. Never wear loose-fitting
clothes or jewelry. Use a hair-net on long hair.
For your own safety, use only the manufacturerʼs
accessories and attachments.
Use only sharp saw blades that are in perfect
Seite 6