Technical Data; Drill Safety Warnings - Milwaukee M18 CRAD2 Manual Original

TECHNICAL DATA

Production code......................................................................
Drilling capacity in steel ..........................................................
Drilling capacity in wood
with ship auger bit ................................................................
with selfeed bit .....................................................................
with hole saw .......................................................................
No-load speed ........................................................................
Torque with battery 4.0 Ah *....................................................
Battery voltage........................................................................
Drill chuck range .....................................................................
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah ... 12,0 Ah) ..
Recommended ambient operating temperature .....................
Recommended battery types..................................................
Recommended charger ..........................................................
Noise information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K = 5 dB(A)) ...................
Sound power level (Uncertainty K = 5 dB(A)) .......................
Wear ear protectors!
Vibration information
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Drilling into metal
Vibration emission value a
Uncertainty K= .....................................................................
* Measured according to Milwaukee Standard N 877318
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may
signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is
switched off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the
total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the
tool and the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

Safety instructions for all operations
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum
speed rated of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
the workpiece, resulting the personal injury.
Always start drilling at low speed and with the bit tip in
contact with the workpiece. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
the workpiece, resulting the personal injury.
14 ENGLISH
470 342 - M18CRAD2_EN62841.indd 14 470 342 - M18CRAD2_EN62841.indd 14
CORDLESS DRILL DRIVER
...............................................
h,D
M18 CRAD2
..................... 4771 09 01...
...000001-999999
..........................1/2 " (12,7 mm)
.......................1-1/4 " (25,4 mm - 6,35 mm)
.....................2-9/16 " (65 mm)
.............................4 " (101,6 mm)
....................0-1500 min
-1
...........................30 Nm
...........................18 V
........................2-13 mm
..............3,89...4,97 kg
......................-18...+50 °C
................... M18B...M18HB
M12-18C, M12-18AC, M12-18FC, M1418C6
........................85,5 dB (A)
........................96,5 dB (A)
........................1,46 m/s
2
..........................1,5 m/s
2
Apply pressure only in direct line with the bit and do
not apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal injury.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses
when working with the machine. The use of protective
clothing is recommended, such as dust mask, protective
gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a
high reactive force. Determine why the insertion tool stalled
and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
17.02.2020 14:45:12 17.02.2020 14:45:12