To Set The Timer - Freestyle SHARK THRESHER Manual De Instrucciones

chronograph display format setting
will blink.
3. Press S2 or S4 button to toggle be-
tween LAP/SPL (lap time on top line
and split time on bottom line) and
SPL/LAP (split time on top line and
lap time on bottom line) format.
4. When finished making the setting,
press S1 button to confirm.
NOTE: Definitions of lap time and
split time:
a) Lap time – individual lap time.
b) Split time – cumulative lap time.
NOTE: The selected chronograph
display format will apply to both chro-
nograph counting and chronograph
recall function.
For the measurement of elapsed time:
In CHRONOGRAPH mode,
1. Press S2 button to start counting.
2. To stop counting, press S4 button.
3. To restart counting and resume from
where it left off, press S2 button
again.
4. To reset to zero, press S4 button to
stop counting and press and hold
S4 button. The message "HOLD
TO RESET" will be displayed for
approximately 2 seconds and the
counter will be reset to zero.
For the measurement of split time:
In CHRONOGRAPH mode,
1. Press S2 button to start counting.
2. While the chronograph is running,
press S2 button once to register a
lap. The lap time and split time of
the registered lap will be displayed
and the lap number will be displayed
intermittently. The chronograph is
still running in the background.
After approximately 10 seconds, the
lap time and split time of the current
lap will be displayed.
3. Repeat the last step until all the laps
have been registered.
4. To stop counting, press S4 button.
5. To restart counting and resume from
where it left off, press S2 button
again.
6. To reset to zero, press S4 button to
stop counting and press and hold
S4 button. The message "HOLD
TO RESET" will be displayed for
approximately 2 seconds and the
counter will be reset to zero.
NOTE: In a chronograph counting, the
watch can register up to a maximum of
99 laps before start counting from lap
1 again. However, only the first 50 lap
records will be stored and available for
checking in recall function.
NOTE: You can leave the chronograph
running while switching over to other
operating modes.
NOTE: You can leave the chronograph
running while switching over to other
operating modes. The chronograph in-
dicator will be displayed in HOME
TIME mode and FOREIGN TIME mode
when the chronograph is in use.
TO USE THE RECALL FUNCTION:
In CHRONOGRAPH mode,
1. Press S1 button to select the recall
function.
2. Press S2 or S4 button to cycle
forward or backward through the
stored lap records.
3. Press S1 button to return to CHRO-
NOGRAPH mode.
NOTE: The recall function is available
only when there is more than 1 lap
record stored.
NOTE: The lap record will be cleared
when the chronograph is reset.

TO SET THE TIMER:

1. Press S3 button to select TIMER
mode.
2. Press S1 button, the message "SET"
will be displayed and the hour
digits will blink. Press S2 button to
increase or S4 button to decrease
the value. Holding down the button
will speed up the process.
3. Press S3 button, the minute digits
will blink. Press S2 button to in-
crease or S4 button to decrease the
value. Holding down the button will
speed up the process.
4. Press S3 button, the second digits
will blink. Press S2 button to in-
crease or S4 button to decrease the
value. Holding down the button will
speed up the process.
5. Press S3 button, the "Action-at-End"
setting will blink. Press S2 or S4
button to toggle between STOP AT
END (STOP) and REPEAT AT END
(REPEAT).
6. When finished making all the set-
tings, press S1 button to confirm.
NOTE: Definitions of Action-at-End
setting option:
a) STOP AT END – the timer will stop
when the countdown reaches zero.
b) REPEAT AT END – the timer will
repeat the countdown when the count-
down reaches zero.
TO USE THE TIMER:
1. Press S3 button to select TIMER
mode.
2. The timer will then be displayed in
its current state – stopped, running,
or reset.
3. To resume a stopped counting, press
S2 button to resume from where
it left off.
4. To start a new counting, reload the
timer first.
Press S4 button to stop counting,
then press S4 button again to reload
the timer.
5. When reaching zero in a countdown,
a tune will be emitted. To stop the
tune, press any button.
TO USE THE BACKLIGHT:
Press S4 button to turn on the back-
light for 3 seconds.
To reduce carbon foot print, these
Freestyle instructions are printed with
soy inks on recycled paper.
ENGLISH