To Set The Timer - Freestyle SPRINT Manual Del Usuario

2. To stop counting, press S1 but-
ton once. Press S1 button again
to resume from where if left off.
3. To reset to zero, press S1 button
to stop counting and then press
and hold S2 button for approxi-
mately 3 seconds.
For the measurement of lap time:
In STOPWATCH mode,
1. Press S1 button to start count-
ing.
2. While the stopwatch is running,
press S2 button once to register
a lap. The lap number and lap
time of the registered lap will be
displayed. The stopwatch is still
running in the background.
After approximately 5 seconds,
the lap number and the elapsed
time of the current lap will be
displayed.
3. Repeat the last step until all the
laps have been registered.
4. To reset to zero, press S1 button
to stop counting and then press
and hold S2 button for approxi-
mately 3 seconds.
NOTE: You can leave the stop-
watch running while switching
over to other operating modes.
The stopwatch indicator
appear as a reminder.
NOTE: In the first hour of count-
ing, the counted time will display
in MM.SS.hh (minutes. seconds.
hundredths). After 1 hour, the
counted time will display in
HH:MM.SS (hours: minutes.
seconds).
NOTE: When the stopwatch has
counted for more than 1 hour,
once the counting is stopped, the
counted time will be displayed
in HH: MM.SS (hours: minutes.
seconds) and MM.SS.hh (minutes.
seconds. hundredths) at an alter-
nate interval of 2 seconds.
NOTE: The stopwatch can record
up to a maximum of 10 laps (first
10 laps).
NOTE: The stopwatch can count
up to a maximum of 99 hours, 59
minutes and 59.99 seconds.
TO USE THE RECALL MODE
1. Press S3 button to select RE-
CALL mode.
2. The total elapsed time [TTL] or
the message "no DATA" (if there
is no stored lap record) will be
displayed.
3. Press S1 button to cycle the
stored lap records in the order
of total elapsed time [TTL], fast-
Freestyle_SPRINT_AG9153-R01.indd 3
est lap time [FAST], slowest lap
time [SLOW], average lap time
[AVG] and individual lap record
[LAP-XX].
4. When the individual lap record
[LAP-XX] is displayed, press
S2 button to cycle the stored
individual lap records.
NOTE: In RECALL mode, the
watch will automatically return to
NORMAL TIME mode if there is no
button pressed for 3 minutes.
NOTE: When the individual lap re-
cord [LAP-XX] is more than 1 hour,
once the counting is stopped, the
lap record will be displayed in HH:
MM.SS (hours: minutes. seconds)
and MM.SS.hh (minutes. seconds.
hundredths) at an alternate inter-
val of 2 seconds.

TO SET THE TIMER

1. Press S3 button to select TIMER
mode.
2. Press S2 button to alter the
timer setting among 1, 3, 5, 10,
15, 25, 30, 45 and 60 minutes.
TO USE THE TIMER
In TIMER mode,
will
1. Press S1 button to start count-
ing.
2. To stop counting, press S1 but-
ton once. Press S1 button again
to resume from where if left off.
3. To reset the timer, press S1
button to stop counting and then
press and hold S2 button for
approximately 2 seconds.
4. After reaching zero in a count-
down, a 20-second beep will be
emitted. To stop the beeping,
press any button, the timer will
reload automatically.
NOTE: You can leave the timer
running while switching over to
other operating modes.
TO USE THE BACKLIGHT
Press S4 button to turn on the
backlight for approximately 3
seconds.
ENGLISH
To reduce carbon foot print, these
Freestyle instructions are printed with
soy inks on recycled paper.
8/30/12 2:37:02 PM