EarthWise LSTM2012-4 Manual Del Propietário página 6

WHEEL ADJUSTMENT
WARNING: Before adjusting the height of the mower deck,
ensure your string trimmer is switched off and disconnected
from the power supply.
The 3-in-1 compact mower deck offers three cutting heights:
1.67'' / 1.9'' / 2.34''.
To adjust the height of the mower deck :

Grasp the front or rear wheel axle of the mower deck and
pull it upwards as shown in Fig. 12.

Then slide the wheel axle up or down within the U-shaped
groove under the deck to set the height. Move the wheel
axle up for shorter-cut grass or down for a longer cut. Move
the front wheel axle down and rear axle up for a medium
cut.

Repeat for each wheel axle until all four wheels are
adjusted to the desired height and are fully in the upper or
lower slots.
NOTE: It may be simpler to adjust the height of your mower
deck if the string trimmer is not attached.
REPLACING SPOOL / CLEARING JAMS AND TANGLED
LINES
From time to time, especially when cutting thick or stocky
weeds, the line feeding hub may become clogged with sap
or other material and the line will become jammed as a
result. To clear the jam, follow these steps.

Turn off the trimmer and remove the battery.

Press the release tabs on the line spool retainer① and
remove the cover② by pulling it straight off.

Remove the line spool③. If necessary, remove any
dirt.

Extend the line jammed or tangled out of the spool
fitting ④ .
Fig.12
WARNING: Remove the trimmer from mower deck before
performing any maintenance.

Do not spray or pour water on the mower deck or
trimmer in an attempt to clean them.

Do not lubricate the wheels.

Clean away built-in dirt and grass in trimmer pocket and
under release lever to allow trimmer to attach correctly.
CAUTION: Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc., come in
contact with plastic parts. They contain chemicals that can
damage, weaken or destroy plastic.
Make sure the battery is detached from the unit, then use
only mild soap and a damp cloth to clean the tool. Never let
OPERATING

Insert the spool in the line receptacle ⑤ .

Thread the end of the line through the eyelet of the
spool retainer ⑥ .

Firmly press both tabs of the spool cover together at
the same time, and push the cap onto the spool until it
engages ⑦ .
REWINDING SPOOL FROM BULK LINE
(USE ONLY .065" DIAMETER LINE)
Bulk line for your trimmer/edger is available at extra cost
from your local dealer. To install bulk line, follow these steps:

Turn off the trimmer and remove the battery.

Press the release tabs on the line spool cover as shown
in Fig. 13, and remove the cover by pulling it straight off.
Remove the spool from the tool and remove and discard
all line on the spool.

Insert one end of the bulk line into the hole in the spool.

Hold the line in the hole and pull the rest of the line
through the slot in the spool.

Snugly and evenly wind the bulk line onto the spool in
the direction of the arrow until it is nearly full.

Insert the line end through the eyelet in the spool hub.
Pull the line through the hole to maintain tension while
placing the spool down into the hub with the notched
side exposed.

Press the spool down GENTLY and rotate it until you
feel it drop into place. (When in place, the spool will turn
a few degrees left and right freely.)

Snap the spool cover back on, insert the battery and
turn the tool on. In a few seconds you'll hear the nylon
line being cut automatically to the proper length.
Fig.13
MAINTENANCE
any liquid get inside the tool; never immerse any part of the tool
into a liquid.
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals Do not store the tool
on or adjacent to fertilizers or chemicals.
IMPORTANT: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment should be performed by
a qualified individual using only identical replacement parts.
If you drop the trimmer, carefully inspect it for damage. If the
guard is bent or cracked, handles broken or if you see any
other condition that may affect the trimmer's operation, it must
be repaired before putting it back into use. Call our customer
service help line at 1-800-633-1501 for assistance.
6
LSTM2012-4