Electrical Connection - NODOR GAT-850 Manual De Usuario

GB
DECORATIVE EXTRACTOR HOODS
Dear client,
We are sure that the purchase of our extractor hood will fully
satisfy all of your needs.
Please read this instruction manual carefully in order to obtain
the best results from the use of the hood.
INSTRUCTIONS FOR INSTALLATION, MAINTENANCE
AND USE
General indications
Before installing and using the hood, be sure that the voltage
(V) and the frequency (Hz) indicated on the feature plate match
the voltage and frequency at the installation site.
The feature plate and technical data are shown on the inside of
the product.
For better performance in extracting fumes we advise that
tubing installed should be of a diameter not less than 120 mm.
We also advise using rigid PVC tubing.
It is advisable to let the appliance work for 15 minutes after the
cooking of the food in order to remove completely the fumes.

ELECTRICAL CONNECTION

Connect the cord to a socket or double pole switch, which
must have a minimum contact opening distance of 3 mm.
The manufacturer shall not be liable for failure to observe all
safety regulations in force for the correct and normal operation
of electrical parts.
INSTALLATION
The hood may be installed to work in two different ways: If
there is a possibility of installing the hood with an evacuation
pipe to the outside, it will be used in aspirating version. If this
possibility does not exist, the hood will be used in the filtering
version, recirculating the air using active carbon filters.
Aspiration: If the hood is used in the ASPIRATING version,
connect the plastic conic outlet piece supplied with the hood
(125 mm diameter) to an evacuation pipe connected directly to
the outside
We recommend the use of a 125 mm. diameter pipe for better
hood performance and lower noise levels.
Filter: This hood can be transformed into an air filter if there is
no possibility of connecting it to the outside. In this case, the
air circulates through opening which you must drill into the
furniture. In order to operate as an air filter, you must use two
active carbon filters which are supplied as separate acces-
sories. The active carbon filters must be replaced periodically
in order to work properly, at least every three months (depen-
ding on how frequency the filter is used)
Mounting and fastening to the furniture
– The accessories needed to install the hood are located inside
the hood.
– The hood must be installed at least 66 cm. from the sto-
vetop.
– The screws needed to fasten the hood are contained in the
bag of accessories which comes with the hood. (Fig. 2).
Five-button control panel
This panel is situated on the front of the extractor and inclu-
des:
- 3 control switches for the motor (speed positions 1, 2 and
3) (ref D)
- Off button of the motor (ref C)
- On/off light of the motor (ref A)
- Light switch (ref. B)
IMPORTANT:
• Do not connect the hood to chimneys, ventilation pipes or
hot air pipes. Before connecting any pipes, consult municipal
ordinances on exhaust air and request permission from the
person in charge of the building. Be sure there is adequate
ventilation, even in cases where the hood is to be used simul-
taneously with another product.
• Never leave frying food unattended since grease can
overheat and catch fire. The risk of fire is even greater in the
case of used oil.
• Never use the hood in areas where devices with exhaust
pipes connected to the outside are already operating unless
perfect ventilation can be guaranteed.
• To avoid the possibility of fire, adhere strictly to all of the
recommendations included here and to the periodic cleaning
of the grease filters.
• During an electrostatic discharge (ESD) it is possible that
the device will stop working. By switching the device OFF an
ON the device will again work as intended. There is no risk and
no risk will appear.
• If the supply cord of this equipment is damaged, it must
only be replaced by manufacturer or it's service agent or simi-
larly qualified person in order to avoid a hazard.
• Never have a lighted flame under the extractor hood.
• The appliance must be placed in such a way, that the
supply plug is accessible.
• The hood must be installed at a minimum distance of
65cm from the stovetop.
• During climatic conditions causing electrical interference,
it is possible that the device may stop working. By switching