Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
DECORATIVE EXTRACTOR HOODS
Dear client,
We are sure that the purchase of our extractor hood will fully
satisfy all of your needs.
Please read this instruction manual carefully in order to obtain
the best results from the use of the hood.
INSTRUCTIONS FOR INSTALLATION, MAINTENANCE AND
USE
If you need any technical help or would like more information
about our products, please do not hesitate to contact our
official distributor.
GENERAL INDICATIONS
Before installing and using the hood, be sure that the voltage
(V) and the frequency (Hz) indicated on the feature plate match
the voltage and frequency at the installation site.
The feature plate and technical data are shown on the inside
of the product.
For better performance in extracting fumes we advise that
tubing installed should be of a diameter not less than 120 mm.
We also advise using rigid PVC tubing.
ELECTRICAL CONNECTION
Connect the cord to a socket or double pole switch, which
must have a minimum contact opening distance of 3 mm.
The manufacturer shall not be liable for failure to observe all
safety regulations in force for the correct and normal operation
of electrical parts.
1- FUNCTION OR PROGRAMMING BUTTON
With the bell completely off, press for 3 seconds and select the
different programming buttons in sequence (time, light and
speeds). The corresponding icon will light up according to the
function selected.
The sections described below show the system for program-
ming the default values.
In the event of a fault with the power supply, the device will
store the programmed speed and light information as the
default but the clock will be deactivated.
a.- SETTING THE TIME. If you press the
for 3 seconds, the time icon
should flash and using the
regulate the time.
.
key just once
lights up. The clock digits
and
you should be able to
The default setting is that the un-programmed time will flash.
At the start, the clock is in 24:H mode and by using the
keys you can select 24H or 12H. If you select 24h, the AM
or PM indicators will not light up. After 2 seconds, if you have
not pressed any key the time digits will flash allowing you to
select the exact time.
If you keep the
or
seconds, the time change speed increases. When you press
the
button again, it should be adjusted and it will go to the
next function. The programming deactivates if you wait 20
seconds.
b.- SELECTING THE LIGHT PROGRAMMING. If you press
the
key again in programming mode, the time icon
go off and the light icon
the brightness you want when you switch on the lights.
Maximum brightness will be the default. To select the bright-
ness, press the
or
programming will be deactivated.
c.- SELECTING THE DEFAULT SPEED. If you press the
key again in programming mode, the light icon
and the motor icon will light up. You can also programme
the speed that you want and that it comes on by default every
time the bell is switch on. The first speed will be the default. To
select the speed, press the
the programming, press the programming key
wait 20 seconds the programming will be deactivated.
2.- START/STOP BUTTON
have programmed (the first speed is the default) and the
corresponding rectangles will light up. If you press the button
again, the motor will stop.
If neither the bell, extractor nor the light function, the display
light will dim.
3.- LIGHT ACTIVATION/DEACTIVATION BUTTON
When you switch the light on, it will be activated at the same
brightness that you have programmed in the programming
function. The
and
can be adjusted temporarily until the light is switched off.
When you turn it back on, it will have the brightness that you
programmed initially.
The light function deactivates after 20 second and returns to
the motor position.
keys pressed for more than 2
will come on. You can programme
keys. If you wait 20 seconds, the
will go off
and
keys. To complete
, or if you
. It starts in the speed that you
keys are active and the brightness
GB
or
will
.
Publicidad
Tabla de contenido
