Product Features; Technical Data - Bosch PCM 8 S Manual Original

OBJ_BUCH-557-006.book Page 30 Wednesday, October 15, 2014 9:24 AM
30 | English
The power tool is not suitable for cutting aluminium or other
non-ferrous metals or alloys.
The light of this power tool is intended to illuminate the power
tool's direct area of working operation and is not suitable for
household room illumination.

Product Features

The numbering of the components shown refers to the repre-
sentation of the power tool on the graphic pages.
1 Dust bag
2 Chip ejector
3 Cable holder
4 Button for releasing the tool arm
5 Handle
6 Blade guard
7 Retracting blade guard
8 Saw blade
9 Roller
10 Fence
11 Holes for quick-action clamp
12 Insert plate
13 Locking knob for various mitre angles
14 Mitre angle indicator
15 Scale for mitre angle
16 Mounting holes
17 Saw table
18 Drill holes for extension bars
19 Extension bar
20 Hex key (size 6 mm)/cross-head screwdriver
21 Stop screw for 45° bevel angle
22 Stop screw for 0° bevel angle
23 Laser beam outlet
24 Lighting unit (Power Light)
25 Slide device
26 Transport handle
27 Laser warning label
28 Switch for light ("LED")
29 Switch for marking of cutting line ("Laser")
30 Depth stop
31 Bevel lock lever
32 Locking screw for slide device
33 Hex socket screws (6 mm) of the fence
34 Recessed handles
35 Transport safety-lock
36 Battery compartment
37 On/Off switch
38 Material stop
39 Saw-table extension
40 Fastening kit for extension bar
41 Casing fin
42 Base unit*
43 Fastening kit for "base unit"*
1 609 92A 0VP | (15.10.14)
44 Spindle lock
45 Hex socket screw (size 6 mm) for mounting of saw blade
46 Clamping flange
47 Interior clamping flange
48 Wing nut for locking of the saw-table extension
49 Quick-action clamp
50 Quick-release button
51 Locking knob of the quick-action clamp
52 Wing nut of the quick-action clamp
53 Indicator for bevel angle
54 Wing nut for locking of the length stop
55 Lock nuts of the depth stop
56 Stop nut of the depth stop
57 Casing stop for depth stop
58 Screws for insert plate
59 Cover
60 Knurled screw
61 Set screw for horizontal laser positioning
62 Set screw for vertical laser positioning
63 Scale for bevel angle
64 Screw for bevel angle indicator
65 Screw for mitre angle indicator
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Sliding Mitre Saw
Article number
Rated power input
No-load speed
Laser type
Laser class
Weight according to
EPTA-Procedure 01/2003
Protection class
Permissible workpiece dimensions (maximum/minimum) see page 34.
Starting cycles generate brief voltage drops. Interference with other
equipment/machines may occur in case of unfavourable mains system
conditions. Malfunctions are not to be expected for system impedances
below 0,24 ohm.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
PCM 8 S
3 603 L02 0..
W 1200
-1
min 5200
nm 650
mW < 1
2
kg 18.7
/II
mm 210
mm 1.4–2.0
mm 30
Bosch Power Tools