Technical Data; Before Commissioning - Scheppach TIGER 2500 Manual De Instrucciones

d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly main-
tained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpect-
ed situations.
5. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of the
power tool is maintained.
m ATTENTION!
This power tool generates an electromagnetic field
during operation. This field can impair active or pas-
sive medical implants under certain conditions. In or-
der to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the machine.
Safety instructions for table-top grinding ma-
chines
a) Do not use damaged tool inserts. Check tool
attachments such as grinding discs for chip-
ping and cracks before each use. Once you
have checked and used the tool attachment,
ensure that you and all other persons in the
vicinity remain outside the plane of the rotat-
ing tool attachment and allow the device to
run for 1 min. at the maximum speed.
Damaged tool attachments usually break during
this test period.
b) The permissible rotational speed for tool at-
tachments must be at least as high as the
maximum speed cited on the electric tool.
Accessories that rotate faster than permitted can
break and fly off at high speed.
c) Never grind on the side surfaces of the grind-
ing disc. Grinding on the side surfaces can cause
the grinding disc to break and fall apart.
20 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Residual risks
m The machine has been built according to the
state-of-the-art and the recognised technical safety
requirements. However, individual residual risks can
arise during operation.
• Danger of injury for fingers and hands due to the
rotating grinding disc.
• Hazard due to electrical power with the use of im-
proper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the "Safety in-
structions" and "Intended use" are observed along
with the complete operating instructions.

7. Technical data

Dimensions L x W x H
Tool rest ø
Grindstone
Grindstone idle speed
Cutting speed
Weight
Motor P1
Power P2
Motor speed
Operating mode
Current rating
Technical changes reserved!
Noise
Total noise values determined in accordance with EN
ISO 4871.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA

8. Before commissioning

• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the
packaging and transport safety devices (if present).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, keep the packaging until the end of the
warranty period.
ATTENTION!
The device and the packaging are not children's toys!
Do not let children play with plastic bags, films or
small parts! There is a danger of choking or suffocat-
ing!
320 x 325 x 335 mm
12 mm
ø 250
90 min
-1
1,2 m/sec
16.3 kg
230 – 240 V / 50 Hz
120 W
1400 min
-1
S1 100%
1,0 A
94 dB(A)
3 dB
107 dB(A)
3 dB