Satco NUVO 63-500 Instrucciones De Instalación Y Seguridad

LED UNDER CABINET
FIXTURE
Models: 63-500, 63-501, 63-502, 63-503, 63-504
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock
• LED Under Cabinet Fixture installation requires knowledge of luminaries'
electrical systems. If not qualified, do not attempt installation. Contact
a qualified electrician.
• To reduce risk of fire and over-heating, secure all connections.
• TURN OFF the electrical power before proceeding.
• The electrical rating of this product is 120V/60Hz.
• To prevent wiring damage or abrasion, do not expose wiring to edges
of sheet metal or other sharp objects.
• Do not make or alter any open holes in an enclosure of wiring or
electrical components during installation.
• Not rated for damp or wet locations.
• This product must be installed in accordance with the owner's manual,
current electrical codes and/or the current National Electric Code (NEC).
WARRANTY: This product is guaranteed for a 5-year warranty. Any
quality issue in normal use within the warranty period, will be repaired or
replaced according to the situation and under the condition specifications
can be provided. Visit www.Satco.com for full warranty details and
dimmer compatibility information.
INSTALLATION: Mounting – Direct
STEP 1: Open the two mounting screw covers located on the
front edge of the fixture (A).
STEP 2: Place the fixture in desired position and mount with
included screws (B).
STEP 3: Close the mounting screw cover.
(A)
Mounting
Screw
Cover
Mounting
Screw
WIRING: Option 1 – Power Cord
STEP 1: Mount the fixture.
STEP 2: Remove the electrical port cover on the INPUT side.
STEP 3: Connect the included power cable to the female port on
the fixture.
STEP 4: Plug the power cable into a 120 Volt outlet.
STEP 5: Bundle the excess power cord with zip ties or twist ties.
Electrical Port
Cover
End-to-End Connector
© Copyright 2021 Satco Products, Inc. 3/21
(B)
Model # Dimensions
63-500
63-501
63-502
63-503
63-504
Mounting – Keyhole
STEP 1: Place the fixture in the desired location and mark the
locations of the keyholes through the wiring area (C).
STEP 2: Install (2) screws into the marked locations.
STEP 3: Mount fixture through 2 keyholes on back of device.
Tighten screws if required (D).
(C)
Option 2 – Hardwire to a Junction Box
(sold separately)
STEP 1: Disconnect power from the breaker or fuse box.
STEP 2: Remove the electrical port cover from the INPUT end.
STEP 3: Use the provided end-to-end connector to link the
junction box to the INPUT side of the fixture.
STEP 4: Connect the OUTPUT end of the end-to-end connector
to the junction box.
STEP 5: Open the junction box and remove the most convenient
of the three knockouts.
STEP 6: Mount the junction box and the fixture to the cabinet.
STEP 7: Attach the 3/8" die-cast connector to the junction box
and pull wiring through it.
STEP 8: Connect wiring using above wiring diagram.
STEP 9: Close the junction box.
1
8"L x 3 1/2"W (203mm x 90mm)
11"L x 3 1/2"W (280mm x 90mm)
14"L x 3 1/2"W (355mm x 90mm)
22"L x 3 1/2"W (559mm x 90mm)
28"L x 3 1/2"W (711mm x 90mm)
WIRING DIAGRAM
(D)
Satco Products, Inc.
Brentwood, NY 11717