Description; Tools And Accessories - Hilti TE 706 Manual De Instrucciones

2. Description

2.1 Use of the power tool as intended
The power tool is designed for medium-duty chiseling
work. It is suitable for breaking/removing and demol-
en ishing concrete, masonry, stone or asphalt. It is intended
for use on construction sites of all kinds.
The power tool may be operated only when connected
to a power supply providing a voltage and frequency in
compliance with the information given on its rating plate.
Changes or modifications to the power tool are not per-
missible.
2.2 Important features of the power tool
2.2.1 Active vibration reduction
The TE 706-AVR is equipped with an active vibration
G
reduction system which cuts vibration to 40 % of that
of the TE 706 (without Active Vibration Reduction).
2.2.2 Theft protection system (option)
The power tool may be equipped with the optional
G
theft protection system. If the power tool is equipped
with this feature, it can be activated and made ready
for operation only by way of the corresponding acti-
vation key.
2.2.3 Chuck
TE-Y (SDSmax) quick-change chuck
G
2.2.4 Switch
On/off switch
G
3-position power level selection switch (100 %, 75 %,
G
50 %)
Chisel adjustment and locking switch (for 24 click-
G
stop positions per revolution)

3. Tools and accessories

TE 706/TE 706-AVR
TE-Y chuck (SDSmax)
Pointed chisel
Flat chisel
Wide-flat chisel
Hollow chisel
Channel chisel
Mortar chisel
Flexible chisel
Bushing tool
Tamping tool
Earth rod rammer
TPS Theft Protection System with Company
Card, Company Remote and TPS-K activation key
Use the Hilti tools listed above. With these tools you will achieve a higher breaking and material removal
performance and longer service life as the power tool and the insert tool have been optimized as a system.
2
Printed: 07.07.2013 | Doc-Nr: PUB / 5071189 / 000 / 00
2.2.5 Grip (with soft synthetic rubber padding)
Two-way adjustable (pivoting) and vibration-absorb-
G
ing side handle
Vibration absorbing grip
G
2.2.6 Safety features
Electronic interlock to prevent unintentional restart-
G
ing after interruption of the power supply (see sec-
tion 9.).
Casing and grip isolated from interior parts of the tool
G
to reduce transmission of heat and vibration.
Automatic electronic overheating and overvoltage cut-
G
out (see section 9.).
2.2.7 Lubrication
Permanent lubrication with separate lubrication cham-
G
bers for the gearing section and hammering mecha-
nism.
2.2.8 Indicator lamps
Service indicator lamp (red, see section 8.3).
G
Theft protection system indicator (available as an
G
option) (yellow, see section 7.2.1).
2.2.9 Items supplied as standard
Power tool
G
Side handle
G
Grease dispenser, 50 ml
G
Cleaning cloth
G
Operating instructions
G
Toolbox complete with overview of the insert tools
G
(chisels) available.
Length (mm)
Width (mm)
280–700
– –
26 280–700
280–500
50–120
28 280
280
22–36
280
38
150 650
250
40 x 40
150 x 150 300
∅ 15–25
300
option
Width (in)
Length (in)
– –
11"–27"
"
3 / 11"–27"
4
"
1
2"–4 / 11"–19"
2
1" 11"
"–1 "
7 1
/ / 11"
8 2
"
15 /
11"
16
" "
5 7 / 25 1 /
8 2
"
5 7 /
10"
8
– – – –
– – – –