General Operation - Zolia ZD-90 Manual De Instrucciones

2. Press the CLOCK key to set the HOUR
3. Press the TIMER key to set the MINUTE
4. Press the SET key once to confirm the time. ​ N ow the display will show either 12 or 24 to indicate the display
mode ​ .
5. Press the CLOCK key to change between 12 or 24-hour display mode
6. Press the START key to CONFIRM the clock setup
7. (1 07) will be flashing and you must now set the feeding times
2. ​ S etting the Feed Time and Number of Feedings per Day
1. (1 07) should now be flashing. Digit-1 is the feeding number (times per day), Digits-3 & 4 are the feeding time
(in hours).
2. The display shows the 1st feeding time (1 07)=(1st feeding at 7am).
3. With (1 07) Flashing, press and hold (for 2 seconds) the SET key until Digit-3 & 4 start flashing (07).
4. Press the TIMER key to set the desired hour for feeding. Note the ( P ) in the top left corner stands for PM when
using 12 hour time.
5. Press the SET key to confirm your setting and proceed to the 2nd feeding time.
6. Repeat step-4 to set the desired hour for feeding the SECOND feeding time.
7. At this point if you want to only feed 2 times per day Press the START key and you're finished.
8. If you wish to feed a 3rd or 4th time each day, do NOT press the START
Tip: If you pressed the SET key a 3​
then press and hold the SET key (for 2 seconds) to start over, remember not to press the SET key after the Second
feeding, press the START key to end your number of feedings per day.
3. ​ S etting the Volume/Portion-Size
1. Press the VOL key to display feed-volume/portion-size
2. Press and hold (for 2 seconds) the SET key until Digit-4 blinks
3. Press the VOL key to set the desired volume
Note: ​ ​ A . Feed-volume of 1 equals ¼ cup (60cc) of food, 2 means ½ cup (120cc) of food, 3= ¾ cups (180cc) and so on.
B.The number 0 represents 10 portions which is equal to 2.5 cups ( liters).
4. Press the START key to confirm the volume/portion size

General Operation

To review the settings
1.Press the TIMER key to cycle through and view the feeding times.​ O nly the feeding times per day that are set will be
displayed. Digit-1 is the feeding number each day, Digit-3 & 4 are the feeding times (in hours). Example: ​ ( 1 07)=(1st
feeding at 7am).
2. Press the VOL key once to view the volume/portion-size and feeding day(s) remaining
3. Press the DAY key to display feeding day(s) remaining
4. Press the CLOCK key once to display the current time, the CLOCK icon will now turn ON
5. If no key is pressed for more than 8 seconds, the display will switch back to show the next feeding time​
icon flashing.
Note:
A. Using the TIMER key to cycle through the feeding times will only display to the number of feedings you set. The
sequence will repeat after the last one is displayed.
st ​
Only the 1 ​
B. feeding time will be displayed if you've set just 1 feeding
C. A flashing timer-icon means the feeding-time has not been reached while a solid timer icon means the
feeding-time has already passed
D. The volume and day display shares the same screen so Digit-1 & 2 are the feeding day(s) remaining while
Digit-4 is the Volume/Portion-size
Setting the Current Clock Time
1. Press the CLOCK key to display the clock
2. The time and clock icon will now be displayed
3. Press and hold (for 2 seconds) the SET key until all digits blink
4. Press the CLOCK key to set the HOUR
5. Press the TIMER key to set the MINUTE
6. Press the SET key once to confirm the time. ​ T he display will show either 12 or 24 to indicate clock display mode
7. Press the CLOCK key to change between 12 or 24 hour display mode
8. Press the START key to confirm the clock setup
Setting the Feed Time and Number of Feedings per Day
1. Press the TIMER key to display the feeding-time
rd​
time, but you did not want to feed 3 times per day, just press the TIMER key and
8
key and repeat from step-4.
w ith the timer ​